Godex HD830i - T Ro Ub Le Sho O Ting; Appe Ndix - Wi- Fi Se Tting

59
6- 8 Tro ub le Sho o ting
Pro b le m So lutio n
The printe r is switc he d o n b ut the d isp la y
do e s no t lig ht up .
♦ C he c k the p o we r sup p ly.。
O ne o r bo th LEDs lig ht up re d a nd printing is
inte rrupte d.
♦ C he c k the so ftwa re se tting s (d rive r se tting s) o r c o mma nd
c o d e s.
♦ Lo o k fo r the e rro r a le rt in the ta b le in Se c tio n 3-
3 Erro r a le rts .
♦
C he c k whe the r the c utte r is func tio ning no rma lly a nd
whe the r it is c utting a t a ll. (Only if a c utte r is insta lle d .)
The la be l sto c k pa sse s thro ug h the printe r
but no im a g e is p rinte d.
♦
Ple a se ma ke sure tha t the la b e l sto c k is lo a d e d the rig ht
wa y up a nd tha t it is suita b le ma te ria l.
♦ Ple a se ma ke sure tha t the rib b o n is lo a d e d c o rre c tly.
The la b e l sto c k ja m s during printing .
♦
C le a r the p a p e r ja m. Re mo ve a ny la b e l ma te ria l le ft o n the
the rma l p rint he a d a nd c le a n the p rint he a d using a so ft
lint-fre e c lo th d ip p e d in a lc o ho l.
The re is no p rinte d im a g e o n pa rt o f
the
la b e l o r the ima g e is b lurre d.
♦ C he c k the the rma l p rint he a d fo r d ust o r o the r d irt (la b e l
ma te ria l o r rib b o n re sid ue ).
♦ C he c k fo r e rro rs in the a p p lic a tio n so ftwa re .
♦ C he c k the rib b o n fo r wrinkle s.
♦ C he c k the p o w e r sup p ly.
♦ Run a se lf te st (Se c tio n 3-2 )
a nd c he c k the te st p rint p a tte rn
to se e w he the r the p rint he a d p rints o ve r the e ntire wid th o f
the me d ium .
♦ C he c k the q ua lity o f the p rint me d ium.
The p rinte d im a g e is po sitio ne d inc o rre c tly
o r a la be l is m isse d o ut d uring printing .
♦ Run the La b e l size c a lib ra tio n func tio n. (Se c tio n 3-2)
♦ C he c k the la b e l he ig ht se tting .
♦ C he c k whe the r the re is p a p e r o r d ust c o ve ring the
se nso r.
♦ C he c k the p a p e r g uid e se tting s.
The c utte r d oe s not c ut o ff the la be ls in a
stra ig ht line .
♦ C he c k whe the r the la b e l sto c k is p o sitio ne d stra ig ht.
The c utte r d o e s no t c ut o ff the la be ls
c o m ple te ly.
♦ C he c k whe the r the la b e l is mo re tha n 0.2 mm thic k.
Whe n using the c utte r, the la b e ls a re no t fe d
thro ug h o r c ut off inc o rre c tly.
♦ C he c k whe the r the c utte r ha s b e e n c o rre c tly insta lle d .
♦
C he c k whe the r the p a p e r g uid e s a re func tio ning c o rre c tly.
The la be l disp e nse r is no t func tio ning
no rm a lly.
♦ C he c k whe the r the re is d ust o n the la b e l d isp e nse r.
♦ C he c k whe the r the la b e l sto c k is p o sitio ne d c o rre c tly.
NO TE
 If a ny p ro b le ms o c c ur tha t a re no t d e sc rib e d he re , p le a se c o nta c t yo ur d e a le r.