Godox V1Pro C - C.fn: Setting Custom Functions; Control with the Cameras Menu; Protection Function

48 49
C.Fn: Setting Custom Functions
Custom Function Signs
m/ft
AF
STBY
RX STBY
SCAN
CH
ID
BEEP
LIGHT
LCD
FEB ACL
TX
Function
Distance indicator
AF-assist beam
Auto sleep setting
Receiver auto
power off timer
Scan the spare
channel
Wireless Channel
ID
Beeper
Backlighting time
LCD contrast ratio
FEB auto cancel
Transmitter
unit control
Options
m
ft
ON
OFF
ON
OFF
60min
30min
OFF
START
01-32
OFF
01-99
ON
OFF
12sec
OFF
ON
-3~+3
ON
OFF
Settings & Description
m
Feet
ON
OFF
ON
OFF
Power off automatically
after 60 minutes of idle
use when the flash is set
as a receiver unit.
Power off automatically
after 30 minutes of idle
use when the flash is set
as a receiver unit.
OFF
Start to scan the spare
channel
Choose channels from
01-32
OFF
Choose any gure from
01-99
ON
OFF
Off in 12 sec.
Always off
Always lighting
7 levels
ON
OFF
OFF
ON
Press the menu button to enter C.Fn settings.
1. The “Verx.x” in the top-right corner refers to the software version.
2. Turn the select dial to select the custom function No. and its parameters.
3. Press set button to select the custom function No. and conrm its setting.
4. After you set the custom function and press <MENU> menu button, the camera
will be ready to shoot.
5. Press and hold the function button 1 <CLEAR> in the MENU interface until “OK” is
displayed on the panel, which means the parameters in C.Fn are reset.
Note
：
Control with the Camera's Menu
If the camera flash is attached to an EOS camera which has a camera control
function, the flash can be controlled using the camera’s menu screen. For the
menu operation procedure, refer to your camera’s instruction manual.
Setting Camera Flash Functions
The following flash functions are settable according to different flash modes.
1. Flash mode
2. Shutter sync
3. FEB
4. Flash exposure compensation
5. Flash ring
6. Clear camera flash’s settings
Custom Functions of Camera Flash
C.Fn-00, C.Fn-01, C.Fn-03, C.Fn-08, C.Fn-10, C.Fn-20, C.Fn-22.
Clear All Flash Custom Functions
* Screens from the EOS-1D Mark III.
Protection Function
1. Over-Temperature Protection
To avoid overheating and deteriorating the flash head, do not re more
than 100 continuous flashes in fast succession at 1/1 full power. After 100
continuous flashes, allow a rest time of at least 10 minutes.
If you re more than 100 continuous flashes and then re more flashes
in short intervals, the inner over-temperature protection function may be
activated and make the recycle time over 10 seconds. If this occurs, allow a
rest time of about 10 minutes, and the flash unit will then return to normal.
When the over-temperature protection is started, <> is shown on the LCD
display.
1. If flash exposure compensation has already been set with the camera flash, flash
exposure compensation cannot be set with the camera. To set it with the camera,
the camera flash’s flash exposure compensation must be set to zero.
2. If any flash custom functions and flash settings other than flash exposure
compensation have been set by both the camera and the flash, the latest settings
will take effect.
Note
：
Number of flashes that will activate over-temperature protection:
Power Output Level
1/1
1/2 (+0.1~+0.9)
1/4(+0.1~+0.9)
1/8(+0.1~+0.9)
1/16(+0.1~+0.9)
1/32(+0.1~+0.9)
1/64(+0.1~+0.9)
1/128(+0.1~+0.9)
1/256(+0.1~+0.9)
Number of Flashes
100
150
300
300
1100
3500
3500
3500
3500
Note: Numbers of flashes of over-temperature protection are different in different zoom values
and different levels.
Flash function settings screen
Flash C.Fn settings screen