GPRINTER GP-1125T - User Manual

Other manuals for GPRINTER GP-1125T

Program Manual85 pages

Operator's Manual17 pages

Quick Installation Guide2 pages

Questions and Answers

J
Jerry HullAug 19, 2025
What to do if my GPRINTER GP-1125T Barcode Reader is not printing due to serial cable issues?
- H
  huntchristopherAug 19, 2025
  If your GPRINTER Barcode Reader is not printing, first ensure the serial cable is properly connected, verifying that the pin configurations on both ends match. Next, confirm that the baud rate settings on both your PC and the printer are identical. For TPSL command mode, a setting of 9600, n, 8, 1 is recommended to enhance reliability. If issues persist, try using a new cable.
B
Brian HuffAug 21, 2025
What to do if my GPRINTER GP-1125T Barcode Reader is not printing due to ethernet cable issues?
- J
  jim48Aug 21, 2025
  If your GPRINTER Barcode Reader is not printing, there are several things you can check regarding the Ethernet cable. First, verify that the RJ-45 green/orange LED indicator is lit. When the printer is actively receiving and processing data, the LED will display an orange color. Next, check if the printer's IP address is assigned via DHCP. Also, ensure that the fixed IP address is correctly configured in the printer's properties. Allow a few minutes for the printer to connect to the server, and then print a self-test page to confirm the printer's IP address. If the problem persists, try using a new Ethernet cable.
N
Natalie GreenAug 23, 2025
How to fix ribbon wrinkle on GPRINTER GP-1125T Barcode Reader?
- G
  george62Aug 23, 2025
  To resolve ribbon wrinkles with your GPRINTER Barcode Reader, reset the label print density and adjust the paper width fixing stand to fit your label paper size. This issue may be caused by unbalanced print head stress, improperly installed ribbon and label, or label feeding not being smooth.
K
Kelly AdkinsAug 26, 2025
What to do if GPRINTER Barcode Reader is missing data when printing?
- R
  rkramerAug 26, 2025
  To resolve a 'Data miss printing' issue on your GPRINTER Barcode Reader, check if the label size setting is correct and matches your actual label paper size. The issue is caused by wrong label paper size setting.
S
Sylvia SalazarAug 27, 2025
Why is the printing quality not good on my GPRINTER Barcode Reader?
- D
  Denise WatsonAug 27, 2025
  If your GPRINTER Barcode Reader's printing quality is not good, try re-installing the ribbon and/or label. Also, clean the print head if there's too much dust or adhesive. In case the issue persists, print a self-test page to check if the printing is complete, which will help determine if a new print head is needed. The issue is caused by ribbon and label improperly installed, too much dust or adhesive on print head, or damaged print head.
G
Gloria OsborneAug 29, 2025
What to do if my GPRINTER GP-1125T Barcode Reader is not printing because of USB cable?
- T
  tiffany15Aug 30, 2025
  If your GPRINTER Barcode Reader is not printing, first check the USB cable connection or try replacing it with a new one. The issue is caused by USB cable improperly connected.
J
Joshua CarrilloAug 31, 2025
What to do if the power indicator is not on for my GPRINTER GP-1125T?
- R
  rgriffinAug 31, 2025
  If your GPRINTER Barcode Reader's power indicator is off, check the power connector and AC outlet to ensure the plugs are correctly connected. Also, make sure the printer power switch is turned on, and the print head is properly closed by pressing the entire print head mechanism or the two arrow locations. Check if the ribbon or label paper has run out and replace if necessary. Ensure the ribbon and label paper are installed correctly, consulting the user manual for guidance. Lastly, address any gap sensor detection errors by adjusting the paper specification and reprinting, and clear any paper jams inside the printer. The issue is caused by connection problems, printer settings, or hardware issues.
H
Heather WoodsSep 2, 2025
Why is my GPRINTER GP-1125T printing not stable?
- A
  Amy RossSep 3, 2025
  If your GPRINTER Barcode Reader is printing unstably, restart the printer and exit Dump Mode, or reset the RS-232 PARAMETER. This is caused by the printer being in HEX Dump mode or an incorrect RS-232 setting.
J
Jesse MooreSep 4, 2025
What to do if my GPRINTER GP-1125T is not printing due to non-standard ribbon?
- R
  Rebecca KerrSep 4, 2025
  If your GPRINTER Barcode Reader is not printing, check if the ribbon model and specification are standard. The issue is caused by ribbon non standard.
O
owenmaxwellSep 8, 2025
What to do if GPRINTER Barcode Reader is not printing correctly?
- C
  cliffordfordSep 9, 2025
  To resolve a GPRINTER Barcode Reader that is not printing, make sure the printing side of the ribbon is touching the label paper. Clean the print head and try printing again. The suggested print density should be set to 7. Also, ensure that the print head cable and step motor cable are securely connected. Finally, verify that the PRINT command is included at the end of the printing file and that a CRLF command is at the end of each line.