EasyManua.ls Logo

Graco LINE LAZER A Series - User Manual

Graco LINE LAZER A Series
48 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
INSTRUCTIONS–P
ARTS LIST
308–105
Rev. G
Supersedes F
and PCN F
GM
5000
GASOLINE-POWERED AIRLESS LINESTRIPER
LINE
LAZER
3000 psi (210 bar) Maximum
Working Pressure
Model 231–133, Series A
With
one gun, RAC IV
DripLess
T
ip Guard,
Size 319 Line Lazer T
ip & Size 517 SwitchT
ip
and 50 foot (15 m) hose
Model 231–141
Same
as 231–133, except includes
Second Gun Kit, 224–097
GRACO INC. P.O. BOX 1441
MINNEAPOLIS, MN
55440–1441
COPYRIGHT
1990, GRACO INC.
This manual contains important
warnings and information.
READ AND RETAIN FOR REFERENCE
02154
NOTE:
This is an example of the English language DANGER label on your spray
-
er
. This label is supplied with the sprayer in other languages. Before operating the
sprayer
, apply a DANGER label in the appropriate language for your operators,
according to the separate instructions supplied with it.
Liquids
can be injected
into the body by high pressure airless spray or
leaks
– especially hose leaks.
Keep
body
clear of the nozzle. Never stop leaks with any part of the body
.
Drain
all pressure before removing parts. A
void accidental triggering of
gun
by always setting safety latch when not spraying.
Never spray without a tip guard.
In case of accidental skin injection, seek immediate
“Surgical
T
reatment”.
Failure to follow this warning can result in amputation or serious
injury.
FIRE
AND
EXPLOSION HAZARD
SKIN INJECTION
HAZARD
READ
AND UNDERSTAND ALL LABELS AND INSTRUCTION MANUALS BEFORE USE
Spray
painting, flushing or cleaning equipment with flammable liquids
in
confined areas can result in fire or explosion.
Use
outdoors or in extremely
well ventilated areas. Ground equipment,
hoses,
containers and objects being sprayed.
Avoid all ignition sources such as static electricity from plastic drop
cloths,
open flames such as pilot lights, hot objects
such as cigarettes,
arcs from connecting or disconnecting power cords or turning light
switches
on and of
f.
Failure to follow this warning can result in death or serious injury
.

Questions and Answers

  • M
    Molly WilcoxAug 11, 2025
    Why won't my Graco LINE LAZER A Paint Sprayer engine start?
    • A
      Andrew WongAug 11, 2025
      If your Graco Paint Sprayer engine or sprayer won’t start, there are several potential causes. First, ensure the engine switch is turned on. Next, check the gas tank and refill if it's out of gas. Also, verify the engine oil level and replenish if the light on the rear of the engine is glowing. Inspect the spark plug cable to ensure it's connected, and replace the spark plug if damaged. Finally, if water is frozen in the pressure control, return it to an authorized Graco dealer for repair.
  • R
    Ronald DuncanAug 17, 2025
    Why is my Graco Paint Sprayer gun spitting paint?
    • J
      Juan BlackAug 18, 2025
      If you're experiencing spitting from the Graco Paint Sprayer gun, it could be due to several reasons. Check for loose connections at the pump intake and tighten them, then prime the pump. Also, the tip could be partially clogged, so clear the tip clog. Ensure that your fluid supply isn't low or empty; refill and prime the pump. Lastly, remove and clean the suction tube, as dried paint particles from a poorly cleaned suction tube assembly could be the cause.
  • L
    Lance MurphyAug 23, 2025
    What to do if paint leaks into wet-cup of Graco LINE LAZER A Paint Sprayer?
    • R
      Raymond WilliamsAug 23, 2025
      If paint is leaking into the wet-cup of your Graco Paint Sprayer, first try tightening the wet-cup just enough to stop the leakage. If the problem persists, the throat packings or the displacement rod may be worn or damaged and need replacement.
  • J
    Jaime FrankAug 30, 2025
    What to do if my Graco LINE LAZER A engine runs but the pump doesn't work?
    • A
      Amanda FrazierAug 30, 2025
      If your Graco Paint Sprayer engine operates but the displacement pump doesn’t, first ensure the pressure control switch is turned on and that the pressure setting isn't too low; increase the pressure if needed. Check and clean the displacement pump outlet filter, tip, or tip filter if they are dirty or clogged. For issues such as a displacement pump rod seized by dry paint, a worn or damaged connecting rod, drive housing, clutch, or pinion assembly, service or replace the respective components. Also, check the wiring connections and have the pressure control checked by an authorized Graco dealer to ensure electrical power is energizing the field.
  • A
    Alyssa MorganSep 4, 2025
    How to fix low displacement pump output on upstroke on Graco LINE LAZER A?
    • M
      Marilyn CraigSep 4, 2025
      Low displacement pump output on the upstroke in your Graco Paint Sprayer can be caused by several factors. Ensure the pump inlet screen is clean. If the piston ball check isn't seating properly, it will need to be serviced. Also, inspect the piston packings and sleeve gasket in the displacement pump for wear or damage, and replace them if necessary.

Graco LINE LAZER A Series Specifications

General IconGeneral
BrandGraco
ModelLINE LAZER A Series
CategoryPaint Sprayer
LanguageEnglish

Related product manuals