Graco LineLazer IV 200HS User Manual (English)

Other manuals for Graco LineLazer IV 200HS

Questions and Answers:

C
Cindy SimmonsSep 2, 2025
Why does my Graco Paint Sprayer work, but the display doesn't?
- K
  Kimberly WarrenSep 3, 2025
  If your Graco Paint Sprayer operates, but the display does not, consider the following: * There may be a bad connection between the control board and the display. Remove the display and reconnect it. * The display may be damaged. Replace the display. * There may be loose cables. Connect the cables to the back of the control board. * The control board LED may not be flashing. Replace the control board.
T
Terry GallegosSep 2, 2025
What to do if the gallon counter on my Graco Paint Sprayer isn't working?
- M
  Maria Jackson DDSSep 2, 2025
  If the gallon counter on your Graco Paint Sprayer is not working, check these potential causes: * A broken or disconnected wire. Check the wires and connections, and replace any broken wires. * A bad sensor. Replace the sensor. * A missing or damaged magnet. Replace the magnet and locate it in the correct spot.
O
ortegacharlesSep 1, 2025
Why is the pressure low on my Graco Paint Sprayer display?
- C
  Charles WilliamsSep 1, 2025
  If a low stall or run pressure is shown on the display of your Graco Paint Sprayer, it could be due to: * A new pump or new packings. The pump break-in period takes up to 100 gallons of material. * A faulty transducer. Replace the transducer.
S
Shawna WilliamsAug 31, 2025
Why does my Graco Paint Sprayer overheat?
- K
  keith52Aug 31, 2025
  If your Graco paint sprayer is overheating, consider these possibilities: * There may be paint buildup on the hydraulic components. Clean them. * The oil level may be low. Fill with oil.
S
Sherry HubbardAug 30, 2025
Why is my Graco Paint Sprayer engine speed high at no load?
- C
  Christy BryanAug 30, 2025
  If your Graco Paint Sprayer has a high engine speed at no load, the issue may be: * A misadjusted throttle setting. Reset the throttle to 3700 -- 3800 engine rpm at no load. * A worn engine governor. Replace or service the engine governor.
X
xtaylorAug 29, 2025
What causes low output on the up-stroke of my Graco Paint Sprayer pump?
- D
  Donna LaneAug 29, 2025
  If the displacement pump on your Graco Paint Sprayer operates, but the output is low on the up-stroke, it could be due to: * A piston ball that is not seating properly. Service the piston ball. * Piston packings that are worn or damaged. Replace the packings.
P
pdavisAug 28, 2025
Why is the fluid delivery low on my Graco Paint Sprayer?
- K
  Kevin WilliamsAug 28, 2025
  If the fluid delivery is low on your Graco Paint Sprayer, here are some possible causes and solutions: * The pressure setting may be too low. Increase the pressure. * The displacement pump outlet filter (if used) may be dirty or clogged. Clean the filter. * The intake line to the pump inlet may not be tight. Tighten it. * The hydraulic motor may be worn or damaged. Bring the sprayer to a Graco distributor for repair. * There may be a large pressure drop in the fluid hose. Use a larger diameter or shorter hose.
E
Eric PatelAug 26, 2025
Why is there excessive paint leakage in my Graco Paint Sprayer?
- L
  Lauren ClarkAug 27, 2025
  If you notice excessive paint leakage into the throat packing nut of your Graco Paint Sprayer, check the following: * The throat packing nut may be loose. Remove the throat packing nut spacer and tighten the throat packing nut just enough to stop the leakage. * The throat packings may be worn or damaged. Replace the packings. * The displacement rod may be worn or damaged. Replace the rod.
T
Tamara JohnsonAug 25, 2025
How to prime a Graco Paint Sprayer if it's difficult?
- D
  dbradfordAug 26, 2025
  If you're finding it difficult to prime the pump on your Graco Paint Sprayer, consider the following: * There may be air in the pump or hose. Check and tighten all fluid connections. Reduce engine speed and cycle pump as slowly as possible during priming. * The intake valve may be leaking. Clean the intake valve, ensuring the ball seat is not nicked or worn and that the ball seats well. Reassemble the valve. * The pump packings may be worn. * The paint may be too thick. Thin the paint according to the supplier’s recommendations. * The engine speed may be too high. Decrease the throttle setting before priming the pump.
A
Andrew VangAug 23, 2025
Why won't my Graco Paint Sprayer engine start?
- J
  johncrawfordAug 25, 2025
  If your Graco Paint Sprayer engine won't start, there are several potential reasons: * The engine switch may be OFF. Turn it ON. * The engine may be out of gas. Refill the gas tank. * The engine oil level may be low. Replenish oil if necessary. * The spark plug cable may be disconnected or damaged. Connect the spark plug cable or replace the spark plug. * The engine may be cold. Use the choke. * The fuel shutoff lever may be OFF. Move the lever to the ON position. * Oil may be seeping into the combustion chamber. Remove the spark plug, pull the starter 3 to 4 times, clean or replace the spark plug, and start the engine. Keep the sprayer upright to avoid oil seepage.

Graco LineLazer IV 200HS Specifications

General

Engine	Honda GX160
Operating Pressure	2000 PSI
Power Source	Gasoline
Material	Steel
Max Flow Rate	0.54 GPM
Flow Rate	0.54 GPM
Paint Capacity	5 gal (19 l)
Hose Length	50 feet
Max Operating Pressure	3300 psi