GW Instek GDS-1102A-U - Appendix; Fuse Replacement

145 pages

To Next Page

To Previous Page

GDS-1000A-U Series User Manual

134

APPENDIX

Fuse Replacement

Procedure

1. Remove the power cord and remove the fuse

socket using a minus driver.

2. Replace the fuse in the holder.

Ratings

T1A, 250V

Main Page

Table of Contents3
Safety Instructions8
Safety Symbols8
Safety Guidelines9
Power Cord for the United Kingdom12
Getting Started13
Main Features13
Panel Overview15
Front Panel15
Rear Panel18
Display19
Setting up the Oscilloscope20
Quick Reference23
Menu Tree and Shortcuts23
CH1/CH2 Key24
Cursor Key 1/225
Cursor Key 2/225
Display Key26
Autoset Key26
Hardcopy Key26
Help Key27
Horizontal Menu Key27
Math Key 1/2 (+/-/X)28
Math Key 2/2 (FFT/FFT Rms)29
Measure Key30
Run/Stop Key30
Save/Recall Key 1/1031
Save/Recall Key 2/1031
Save/Recall Key 3/1032
Save/Recall Key 4/1032
Save/Recall Key 5/1033
Save/Recall Key 6/1033
Save/Recall Key 7/1034
Save/Recall Key 8/1034
Save/Recall Key 9/1035
Save/Recall Key 10/1035
Trigger Key 2/636
Trigger Key 1/636
Trigger Key 3/637
Trigger Key 4/637
Trigger Key 5/638
Trigger Key 6/638
Utility Key 1/10 (Utility #1)39
Utility 2/10 (Utility #2)39
Utility Key 3/10 (Utility #3)40
Utility Key 4/10 (Hardcopy -Save All)40
Utility Key 5/10 (Hardcopy -Save Image)41
Utility Key 6/10 (Probe Compensation)41
Utility Key 7/10 (Go-Nogo)42
Utility Key 8/10 (Data Logging 1/2)42
Utility Key 9/10 (Data Logging 2/2)43
Utility Key 10/10 (Self CAL Menu)43
Default Settings44
Built-In Help45
Measurement46
Basic Measurements46
Activating a Channel46
Using Autoset47
Running and Stopping the Trigger49
Changing the Horizontal Position and Scale50
Changing the Vertical Position and Scale51
Using the Probe Compensation Signal52
Automatic Measurements54
Measurement Items54
Automatic Measurement Gating56
Automatically Measuring the Input Signals57
Cursor Measurements60
Using the Horizontal Cursors60
Using the Vertical Cursors61
Math Operations62
Overview62
Adding, Subtracting or Multiplying Signals63
Using the FFT Function64
Go No-Go Testing66
Overview66
Edit: Nogo When67
Edit: Source67
Edit: Nogo Violation Conditions68
Edit: Template (Boundary)68
Run Go-Nogo Tests72
Data Logging73
Overview73
Edit: Source74
Edit: Setup Parameters74
Run Data Logging76
Configuration77
Acquisition77
Selecting the Acquisition Mode77
Selecting Delay Mode79
Real Time Vs Equivalent Time Sampling Mode81
Display82
Selecting Vector or Dot Drawing82
Accumulating the Waveform82
Adjusting the Display Contrast83
Selecting the Display Grid83
Horizontal View84
Moving the Waveform Position Horizontally84
Selecting the Horizontal Scale84
Selecting the Waveform Update Mode85
Zooming the Waveform Horizontally86
Viewing Waveforms in the X-Y Mode87
Horizontal Adjustment Menu88
Vertical View (Channel)90
Moving the Waveform Position Vertically90
Selecting the Vertical Scale90
Selecting the Coupling Mode90
Expand Vertical Scale Center / Ground91
Inverting the Waveform Vertically92
Limiting the Waveform Bandwidth93
Probe Attenuation Level and Type93
Trigger95
Trigger Type95
Trigger Parameter95
Configuring Holdoff97
Configuring the Edge Trigger98
Configuring the Video Trigger99
Configuring the Pulse Width Trigger100
Manually Triggering the Signal102
Remote Control Interface103
System Settings104
Selecting the Language104
Viewing the System Information104
Save/Recall106
File Structures106
Display Image File Format106
Waveform File Format106
Setup File Format109
Using the USB File Utilities110
Quick Save (Hardcopy)112
Save114
File Type/Source/Destination114
Saving the Panel Settings115
Saving the Waveform116
Saving the Display Image118
Saving All (Panel Settings, Display Image, Waveform)119
Recall121
File Type/Source/Destination121
Recalling the Default Panel Settings122
Recalling a Reference Waveform to the Display123
Recalling Panel Settings123
Recalling a Waveform124
Recall Image126
Maintenance128
Vertical Resolution Calibration128
Probe Compensation129
Faq131
The Input Signal Does Not Appear in the Display131
I Want to Remove some Contents from the Display131
The Waveform Does Not Update (Frozen)132
The Probe Waveform Is Distorted132
Autoset Does Not Catch the Signal Well132
I Want to Clean up the Cluttered Panel Settings132
The Saved Display Image Is too Dark on the Background132
The Accuracy Does Not Match the Specifications133
The Oscilloscope will Not Allow a 2M Waveform to be Saved133
Appendix134
Fuse Replacement134
GDS-1000A-U Series Specifications135
Model-Specific Specifications135
Common Specifications136
Probe Specifications138
GDS-1072A-U Probe138
GDS-1102A-U Probe138
GDS-1152A-U Probe139
Dimensions140
EC Declaration of Conformity141
Index143

GW Instek GDS-1102A-U - Appendix; Fuse Replacement

Table of Contents

Related product manuals