EasyManua.ls Logo

Hankscraft Runxin RevV4 User Manual

Hankscraft Runxin RevV4
57 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #54 background image
RevV4 Valves & Systems Service Manual
54
Hankscraft Runxin, LLC 300 Wengel Drive 608.524.9465 hrh2o.com sales@hrh2o.com
Any parts used for replacement are warrantied for the remainder of the original warranty period applicable to
the part from the date of manufacture so long as the parts are installed by a Hankscraft Runxin factory trained
and authorized installer.
Hankscraft Runxin's obligation by this Limited Warranty, at is option, is to repair or replace any warrantied
product only. Labor for repair or replacement is not included as part of this warranty. Prior to returning the
product to Hankscraft Runxin, a valid return materials authorization number must be obtained from Hankscraft
Runxin. Any product returned to Hankscraft Runxin without a valid return authorization number will be rejected.
Any product found to be defective will, at the sole discretion of Hankscraft Runxin, be repaired or replaced.
Hankscraft Runxin is not responsible for shipping cost to the repair facility. This section lists the sole remedies
for any valid warranty claim.
This warranty does not apply to defects reported to Hankscraft Runxin outside of the warranty period.
This warranty does not apply to defects caused by installing, operating, servicing, modifying, repairing or
maintaining (or lack of maintaining) the product outside of Hankscraft Runxin's recommendations. Filters,
membrane elements and flow restrictors that become fouled or plugged due to excessive turbidity, dissolved
solids, or microorganisms are not covered by this warranty. This warranty does not apply to defects caused by
damage during shipment, neglect, misuse, modification, accident, noncompliance with local codes and
ordinances, hot water, frozen water, sediment, corrosive liquids, gases, chemicals, bacteria, animals, sand, salt,
flood, wind, fire, outdoor installations where the product is not reasonably covered, pneumatic use, natural
disasters, war, terrorism or acts of God. No other person is authorized to make any other warranty on behalf of
Hankscraft Runxin either during or after the applicable warranty period.
Hankscraft Runxin assumes no liability for determining the proper products and equipment or installation
necessary to meet the requirements of the user of the product, and Hankscraft Runxin does not authorize others
to assume such liability on its behalf.
THE WARRANTIES AND REMEDIES HEREIN ARE EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER WARRANTIES
OR REMEDIES EITHER EXPRESSED OR IMPLIED, HEREIN OR ELSEWHERE, INCLUDING WITHOUT LIMITATION
WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, NON-INFRINGEMENT OR
WARRANTIES RESULTING FROM COURSE OF PERFORMANCE, COURSE OF DEALING OR FROM USAGE OF TRADE.
HANKSCRAFT RUNXIN HEREBY DISCLAIMS ALL OTHER WARRANTIES. HANKSCRAFT RUNXIN'S LIABILITY SHALL
NOT EXCEED THE COST OF THE PRODUCT. HANKSCRAFT RUNXIN IS NOT RESPONSIBLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR EXPENSES OF ANY KIND WHATSOEVER, INCLUDING LOSS OF PROFITS, UNDER
ANY CIRCUMSTANCES AND REGARDLESS OF WHETHER HANKSCRAFT RUNXIN WAS AWARE OF THE
POSSIBILITY OF ANY SUCH LOSS.
Question and Answer IconNeed help?

Do you have a question about the Hankscraft Runxin RevV4 and is the answer not in the manual?

Hankscraft Runxin RevV4 Specifications

General IconGeneral
BrandHankscraft Runxin
ModelRevV4
CategoryControl Unit
LanguageEnglish

Summary

2. Product Features and Applications

3. Product Dimensions and Specifications

4. Pre-Installation Checklist

5. Valve Installation

Control Valve Installation

Step-by-step guide for installing the control valve onto the mineral tank.

6. Bypasses

7. Programming: Display and Instructions

Basic Programming

Adjust time values for each phase of operation.

Mode A-01: Meter Delay

Configures regeneration based on capacity and time delay.

Mode A-02: Meter Immediate

Configures immediate regeneration upon reaching zero capacity.

Mode A-03: Intelligent Meter Delay

Intelligent delay mode using capacity, hardness, and people count.

Mode A-04: Intelligent Meter Immediate

Intelligent immediate mode using capacity and hardness.

Mode A-05: Remaining Compare

Compares usage to historical data for regeneration timing.

Mode A-06: By Day (Timer)

Regeneration based on programmed service days and time.

Mode A-07: Filter Meter

Filter mode regeneration based on capacity and time.

8. PCB Functions and Connections

9. System Installation

System Start-Up

Steps to follow for initial system start-up and verification.

10. Assembly Drawings and Parts List

11. Troubleshooting

Control Valve Troubleshooting

Lists common problems and their solutions for the control valve.

Electronics Troubleshooting

Addresses issues related to the control valve's electronic components and display.

12. Replacement Parts

15. Hankscraft Runxin, LLC Warranty Statement

16. System Configuration and Settings

17. Factory Default Settings