Need help?Do you have a question about the Hantek DSO2D10 and is the answer not in the manual?
General| Bandwidth | 100 MHz |
|---|---|
| Channels | 2 |
| Sample Rate | 1 GSa/s |
| Vertical Sensitivity | 2 mV/div to 10 V/div |
| Trigger Modes | Edge, Pulse, Video, Slope, Alternate |
| Interface | USB Host, USB Device |
| Math Functions | +, -, *, /, FFT |
| Vertical Resolution | 8 bits |
| Display Resolution | 800 x 480 pixels |
| Power Supply | 100-240 V AC, 50/60 Hz |
| Weight | 2.5 kg |
| Display | 7 inch LCD |
| Built-in Generator | Yes, 25 MHz |
| Input Impedance | 1 MΩ ± 2% |
Essential safety guidelines to prevent injury and equipment damage during operation.
Defines safety terms and explains symbols used on the product for hazard identification.
Guidelines for responsible disposal and recycling of the device to minimize environmental impact.
Procedures for checking, preparing, and setting up the oscilloscope for first-time use.
Introduction to the oscilloscope's front panel layout and user interface elements.
Steps for performing functional checks and guidelines for probe connection and safety.
How to perform manual probe compensation and set probe attenuation for accurate measurements.
Explanation of the oscilloscope's menu structure and the function of various control keys.
Details on operation modes, shortcut buttons, and vertical/horizontal controls.
Overview of trigger system parameters, signal sources, and oscilloscope connectors.
Description of multifunctional knobs and softkey usage for operations.
Features for oscilloscope setup and operation of horizontal controls.
Explanation of vertical controls, including offset, Volts/Div, and related settings.
Introduction and step-by-step guide for math operations on channel waveforms.
Explanation of FFT analysis and steps for displaying FFT waveforms.
How to display FFT waveforms and select window functions for spectral analysis.
Basic concepts of trigger source, mode, level, force trigger, and holdoff.
Step-by-step guide to configure edge trigger parameters.
Steps to configure pulse trigger parameters.
Guide to set up video trigger parameters.
Steps to configure slope trigger.
Instructions for setting up overtime trigger.
Steps to configure window trigger.
Guide to set up pattern trigger.
Instructions for setting up interval trigger.
Steps to configure under amp trigger.
Guide to set up UART trigger parameters.
Steps to configure LIN trigger.
Instructions for setting up CAN trigger.
Steps to configure SPI trigger.
Guide to set up IIC trigger.
Explanation and interpretation of UART protocol decoding.
Explanation and interpretation of LIN protocol decoding.
Explanation and interpretation of CAN protocol decoding.
Explanation and interpretation of SPI protocol decoding.
Explanation and interpretation of IIC protocol decoding.
Details on file types and procedures for internal save/recall.
Procedures for saving and recalling files to and from external USB storage devices.
Instructions for saving the oscilloscope's current screen display as a picture file.
Features for managing files on external storage.
Method for making visual estimates and measurements using graticule.
How to use cursors for measurements and explanation of modes.
How to perform automatic calculations of waveform parameters.
List of 32 types of automatic measurements with descriptions.
Configuration for delay, gate measurements, and usage of the Digital Voltmeter function.
How to start, stop, and single-shot acquisition of waveforms.
Explanation of different acquisition modes.
How to use XY mode to analyze phase differences.
How the waveform display rolls from right to left.
Configuration options for waveform display.
Overview of utility functions.
Step-by-step instructions for updating the oscilloscope's firmware.
How to perform self-calibration for optimal measurement accuracy.
Using the Pass/Fail function to judge input signals.
Explains the functions of dedicated buttons and Auto Scale.
Options available when Auto Scale detects a sine wave.
How to restore the oscilloscope to its factory default settings.
Details which settings are reset to default.
How to enter and exit the dual-window display mode.
Steps to set the desired waveform type and its parameters.
How to configure amplitude (AM) and frequency (FM) modulation.
How to set up burst mode.
Instructions for using the WaveEditor software.
Overview of tools and standard shapes in WaveEditor.
How to download and output arbitrary waveforms.
Steps for connecting via USB and installing IO drivers.
Information on using Keysight IO software.
Steps to diagnose and resolve power-on issues.
Steps to resolve issues with waveform display.
Steps to resolve triggering issues.
Information on how to contact HANTEK support.
Recommendations for general care.
Instructions for cleaning.
Technical specifications for horizontal and vertical axes.
Specifications for acquisition modes and trigger parameters.
Detailed specifications for various trigger types.
Specifications for serial protocol triggers.
Specifications for inputs, measurements, and DVM.
Specifications for math, FFT, storage, and AWG.
Specifications for AWG and modulation.
Specifications related to display and interface.
Specifications for environment and mechanics.
List of standard accessories.
Table detailing harmful substance content.
To Next Page
