What to do if Harman Kardon AVR 171 Receiver has front-panel display lights, but there’s no sound or picture?
If the front-panel display lights up on your Harman Kardon Receiver but you're not getting any sound or picture, here are a few things to check: * Make sure all input and speaker connections are secure. * Ensure that the mute button is not activated by pressing it. * Verify that the volume control isn't turned down; increase the volume.
How to troubleshoot a Harman Kardon AVR 171 Receiver that does not function?
If your Harman Kardon Receiver isn't functioning, start by ensuring that the power cord is properly plugged into a working AC power outlet. Also, check if the AC outlet is switch-controlled.
Why Harman Kardon AVR 171 Receiver does not respond to remote control commands?
If your Harman Kardon Receiver isn't responding to the remote control, try these steps: 1. Replace the batteries in the remote. 2. Make sure there's a clear line of sight between the remote and the receiver's front-panel remote sensor.
What to do if there is no sound from any speaker connected to Harman Kardon AVR 171?
If you're not getting any sound from any speaker connected to your Harman Kardon Receiver, it could be in protection mode. This might be due to a short circuit. Check all speaker wires at both the speaker and AVR connections for any crossed wires. If that doesn't solve the issue, the amplifier may have internal problems, and you should contact your local Harman Kardon service center.
Why is there no sound from center or surround speakers on my Harman Kardon Receiver?
If you're not hearing sound from the center or surround speakers on your Harman Kardon Receiver, consider the following: * Ensure you've selected a surround mode other than stereo. * Be aware that monophonic programs do not contain surround information. * Verify the speaker configuration in the setup menu. * Understand that stereo program material may not always generate center or surround channel information.
What to do if remote buttons light, but Harman Kardon AVR does not respond?
If the remote buttons light up but your Harman Kardon AVR isn't responding, the remote might be in Zone 2 mode. Try pressing the Zone 2 button; it won't illuminate when the remote is in Zone 1 control mode.
Why is there intermittent buzzing in tuner of my Harman Kardon AVR 171 Receiver?
If you're experiencing intermittent buzzing in the tuner of your Harman Kardon Receiver, it could be due to local interference. Try moving the AVR or antenna away from computers, fluorescent lights, motors, or other electrical appliances.
How to fix surround-back speaker settings that cannot be accessed on Harman Kardon AVR 1710/AVR 171?
If you cannot access surround-back speaker settings and the test tone doesn't play through the surround back speakers on your Harman Kardon AVR 1710/AVR 171, it may be because multi-zone operation has been selected or assigned AMP channels have been assigned to Zone 2. Use the Speaker Setup menu to reassign the Assigned AMP to the surround back left and right channels.
General| Receiver type | Surround |
|---|---|
| Output impedance | 75 Ω |
| Input sensitivity | 250 mV |
| Maximum input power | 510 W |
| Audio output channels | - channels |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Total Harmonic Distortion (THD) | 0.07 % |
| Power output per channel (20-20KHz@8 Ohm) | 100 W |
| HDMI in | 6 |
| AC (power) in | Yes |
| Composite video in | 1 |
| Digital audio optical in | 2 |
| Headphone connectivity | 3.5 mm |
| Speakers connectivity type | - |
| AM band range | 522 - 1620 kHz |
| FM band range | 87.5 - 108 MHz |
| Supported radio bands | AM, FM |
| Internet radio services supported | iTunes |
| Cable length | 1.8 m |
| Product color | Black |
| Audio decoders | Dolby TrueHD, DTS-HD |
| Volume control | Digital |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Number of products included | 1 pc(s) |
| Receiver dimensions (WxDxH) | 440 x 300 x 121 mm |
| AC input voltage | 220-240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 0.5 W |
Weight and Dimensions| Depth | 300 mm |
|---|---|
| Width | 440 mm |
| Height | 121 mm |
| Weight | 5100 g |
Lists the items included with the AVR.
Details safety precautions for using the AVR.
Provides guidelines for placing the AVR for optimal performance and safety.
Identifies and explains the controls on the front panel of the AVR.
Illustrates and labels the input and output connectors on the rear panel of the AVR.
Details the functions of each button on the system remote control.
Introduces home theater concepts and guides speaker placement.
Explains various audio, video, speaker, and network connection types.
Guides remote setup, AVR configuration, sources, network, and Bluetooth.
Guides everyday use, volume, sources, and media playback from various sources.
Explains advanced features, audio processing, and surround modes.
Guides manual speaker setup, distance, levels, and multizone operation.
Guides customization of AVR features and provides solutions for common problems.
Lists technical specifications and reference tables.
To Next Page