Page 43
align them as shown in the Pictorial. Space the resistors 112"
J
NOTE:
When you connect resistors in the fol~owing steps.
(
Connect a 30 kS2 resistor from the negative lug of
capacitor 5 (NS) to the negative lug of capacitor
6
from the capacitors as shown in the inset drawing. After
6-2).
fitting and soldering the resistors, cut off and discard any
excess lead lengths. No resistor should be closer than 114" to
(,)
place the bent end
of
a
1-5/8"
bare
wire
in
the
,..
any metallic object to which
it
is not intentionally
negative lug of capacitor 7 (NS) and the straight end in
connected.
the positive lead of capacitor
8
(NS).
(4
Refer to the Pictorial and place one of the 314"
lengths of slewing on one lead of a 30 kS2 resistor.
Connect this lead to the positive (marked
+)
lug of
capacitor 1 (NS). Pass the other resistor lead through
.
the positive lug of capacitor 2 6-2) to the negative lug
of capacitor 4 (NS).
(
d
Place one of the 314" lengths of slewing on one lead
of a 30 kS2 resistor and connect this lead to the
positive lug of capacitor 5 (NS). Pass the other lead
through the positive lug of capacitor
6
(S-2) to the
negative lug of capacitor 8 (NS).
(4
Pass the straight end of one of the 1-518" bare wires
through the negative lug of capacitor 2 (NS). Place the
bent end of the wire into the positive lug of capacitor
1 6-2).
Id
Connect the black hookup wire coming from hole
B
on the circuit board to the negative lug of capacitor 1
(NS).
a 30 kS2 resistor from the negative lug of
capacitor 1 6-21 to the negative lug of capacitor 2
6-21.
/
('
)
Connect the bent end of one of the 1-518" bare wires
to the negative lug of capacitor 3 (NS) and the straight
end to the positive lug of capacitor
4
(NS).
J
(
)
Place a 314" length of slewing on one lead of a 30 kS2
resistor and connect this lead to the negative lug of
capacitor 3 (S-2). Connect the other lead to the
negative lug of capacitor
4
(S-2).
(
/
)
Place a 314" length of sleeving on one lead of a 30 kS2
resistor and connect this lead to the negative lug of
capacitor
7
6-21. Connect the other lead to the
negative lug of capacitor
8
(S-2).
(J)
Connect the blue wire from hole
H
of the circuit
board to the positive lug of capacitor
7
(NS).
(
Vr/
Connect one lead of a 30 kS2 resistor to the positive
lug of capacitor
7
6-2). Connect the other lead to the
positive lug of capacitor
8
(S-2).
/'-
(
)
Connect one lead of a 30 kS2 resistor to the positive
lug of capacitor 3 (NS). Connect the other lead to the
positive lug of capacitor
4
6-21.
(4
Connect the bent end of the 1-318" length of bare
wire to the positive lug of capacitor 3 (NS) and the
straight end to the negative lug of capacitor 5 6-2).
(4
Pan a 7-114" length of clear slewing over the red and
the red-yellow wires coming from the
HV
transformer.
Slide the slewing on the wires as far as
it
will go.
(4)
Cut off the redyellow wire
1/2"
beyond the end of
the slewing. Remove 114" of ir?sulation.
(d
Connect the red-yellow wire to the positive lug of
capacitor 3 6-31.
J
I
Carefully compare your work in the foregoing steps to
(
1
Place the bent end of a 1-518" bare wire in the positive the Pictorial (and the Details) for wiring errors and for
lug of capacitor 5 (S-2), and the straight end in the
proper capacitor polarity. Incorrect connections in
negative lug of capacitor
6
(NS).
this high-voltage circuit area can cause serious damage.
To Next Page
Loading...
