HEIDENHAIN TNC 426 PB - Page 926

December 2001 PLC Program Example 7 – 77
NP_W1032_REFERENCE_NECES GLB_NC.DEF : 84 W1032
MAIN_PGM.SRC L:12
PN_W1038_CLOSED_LOOP_OPE GLB_NC.DEF : 85 W1038
AXIS.SRC L:360 =:362 L:429 =:431 L:483
=:485
PN_W1040_CLOSED_LOOP_OPE GLB_NC.DEF : 86 W1040
AXIS.SRC L:364 =:366 L:434 =:436 L:479
=:481
PN_W1042_SUPERVISION_INA GLB_NC.DEF : 87 W1042
AXIS.SRC L:368 =:370 L:442 =:444
PN_W1044_ACTUL_NOMINAL_T GLB_NC.DEF : 88 W1044
AXIS.SRC L:372 =:374 L:438 =:440
PN_W1046_MANUEL_DIRCETIO GLB_NC.DEF : 89 W1046
DIRCBUT.SRC =:294
PN_W1048_MANUEL_DIRECTIO GLB_NC.DEF : 90 W1048
DIRCBUT.SRC =:296
PN_W1050_JOG_MODE_POSIT_ GLB_NC.DEF : 91 W1050
DIRCBUT.SRC =:289
PN_W1052_JOG_MODE_POSIT_ GLB_NC.DEF : 92 W1052
DIRCBUT.SRC =:291
PN_W1054_REFERENCE_ENDSW GLB_NC.DEF : 93 W1054
REF_ENDL.SRC =:234
WG_MOTOR_TEMP GLB_TCMB.DEF : 50 W4068
HELPDIAG.SRC >=:772
WG_MOTOR_TEMP_1 GLB_TCMB.DEF : 51 W4068
INITI472.SRC =:56
WG_MOTOR_TEMP_2 GLB_TCMB.DEF : 52 W4070
INITI472.SRC =:58
WG_MOTOR_TEMP_3 GLB_TCMB.DEF : 53 W4072
INITI472.SRC =:60
WG_MOTOR_TEMP_4 GLB_TCMB.DEF : 54 W4074
INITI472.SRC =:62
WG_MOTOR_TEMP_5 GLB_TCMB.DEF : 55 W4076
INITI472.SRC =:64
WG_MOTOR_TEMP_S GLB_TCMB.DEF : 56 W4078
INITI472.SRC =:66
WG_ACTIVE_PWM_AXIS GLB_TCMB.DEF : 47 W4082
INITI472.SRC =:128 L:131 =:134
AXIS.SRC A:350
WG_SERVO_ENABLE_INTERNAL GLB_TCMB.DEF : 46 W4084
AXIS.SRC =:351
HELPDIAG.SRC LN:752 L:754
WG_MP10_ACTIVE_AXIS GLB_TCMB.DEF : 45 W4086
- not used -
__D0 INITI472.SRC : 139 D0
INITI472.SRC PL:153
PN_D756_S_NOMINAL_RPM_PL GLB_NC.DEF : 97 D756
GEAR.SRC =:612 L:716
I_REF_ENDSWITCH_1_AXIS GLB_IOMB.DEF : 7 I0
REF_ENDL.SRC L:222
I_REF_ENDSWITCH_2_AXIS GLB_IOMB.DEF : 8 I1
REF_ENDL.SRC L:224
I_REF_ENDSWITCH_3_AXIS GLB_IOMB.DEF : 9 I2
REF_ENDL.SRC L:226
I_SERVO_READY_1 GLB_IOMB.DEF : 28 I3
AXIS.SRC ON:306 ON:457
SPINDLE.SRC ON:579
I_SERVO_READY_2 GLB_IOMB.DEF : 29 I3
AXIS.SRC ON:307 ON:458
SPINDLE.SRC ON:580
I_FEED_ENABLE GLB_IOMB.DEF : 13 I3
DIRCBUT.SRC L:245
PLC program example