HEIDENHAIN TNC 430 PA - Page 923

7 – 74 HEIDENHAIN Technical Manual TNC 426, TNC 430
MG_CLOSED_LOOP GLB_TCMB.DEF : 18 M992
- not used -
MG_2_CLAMP_MODE_ACTIV GLB_TCMB.DEF : 20 M993
INITI472.SRC R:39
MG_3_CLAMP_MODE_ACTIV GLB_TCMB.DEF : 21 M994
INITI472.SRC R:40
MG_4_CLAMP_MODE_ACTIV GLB_TCMB.DEF : 22 M995
INITI472.SRC S:41
MG_5_CLAMP_MODE_ACTIV GLB_TCMB.DEF : 23 M996
INITI472.SRC S:42
MG_S_CLAMP_MODE_ACTIV GLB_TCMB.DEF : 24 M997
- not used -
I_5_AXIS_MINUS GLB_IOMB.DEF : 23 M3980
DIRCBUT.SRC L:280
I_5_AXIS_PLUS GLB_IOMB.DEF : 22 M3981
DIRCBUT.SRC L:269
MG_ACTIVE_PWM_AXIS GLB_TCMB.DEF : 26 M3982
INITI472.SRC S:120 LB:127
HELPDIAG.SRC L:767
MG_ACTIVE_PWM_AXIS_1 GLB_TCMB.DEF : 27 M3982
- not used -
MG_ACTIVE_PWM_AXIS_2 GLB_TCMB.DEF : 28 M3983
- not used -
MG_ACTIVE_PWM_AXIS_3 GLB_TCMB.DEF : 29 M3984
- not used -
MG_ACTIVE_PWM_AXIS_4 GLB_TCMB.DEF : 30 M3985
- not used -
MG_ACTIVE_PWM_AXIS_5 GLB_TCMB.DEF : 31 M3986
- not used -
MG_ACTIVE_PWM_AXIS_S GLB_TCMB.DEF : 32 M3987
INITI472.SRC L:129
MG_GEAR_CHANGE_ACTIV GLB_TCMB.DEF : 15 M3990
GEAR.SRC AN:639 AN:648 S:657 R:724
MG_SPINDLE_ON_GEAR GLB_TCMB.DEF : 14 M3991
GEAR.SRC S:709 R:725
MG_SPINDLE_RPM_ZERO GLB_TCMB.DEF : 13 M3992
- not used -
MG_T_I_N_SUPERVISION GLB_TCMB.DEF : 12 M3993
DIRCBUT.SRC AN:239
AXIS.SRC O:459
SPINDLE.SRC O:549 O:562 O:577
HELPDIAG.SRC =:797
MG_SPI_POS_M19_R_M0X GLB_TCMB.DEF : 11 M3994
SPINDLE.SRC L:530 LN:535 L:547
MG_SPINDLE_OFF_M05 GLB_TCMB.DEF : 10 M3995
SPINDLE.SRC O:548 L:561 L:576
MG_SPINDLE_ON_M04 GLB_TCMB.DEF : 9 M3996
SPINDLE.SRC L:543
MG_SPINDLE_ON_M03 GLB_TCMB.DEF : 8 M3997
SPINDLE.SRC L:539
MG_ZERO_MARKER GLB_TCMB.DEF : 7 M3998
INITI472.SRC L:33 R:34
GEAR.SRC PS:721
MG_ONE_MARKER GLB_TCMB.DEF : 6 M3999
INITI472.SRC LN:30 S:31 L:36
AXIS.SRC L:376
GEAR.SRC L:723
NP_M4000_S_IN_POSITION GLB_NC.DEF : 7 M4000
SPINDLE.SRC A:536
NP_M4001_S_ANALOG_NOT_IN GLB_NC.DEF : 8 M4001
SPINDLE.SRC A:587
NP_M4002_S_ANALOG_0_V GLB_NC.DEF : 9 M4002
SPINDLE.SRC L:567 ON:571
GEAR.SRC PS:664
PN_M4005_S_M03_ANALOG_VO GLB_NC.DEF : 11 M4005
SPINDLE.SRC S:540 R:544 R:551 LN:554 O:563
L:569
PLC program example