What to do if 4 LEDs blink on my Hilti Saw?
If 4 LEDs blink on your Hilti Saw, it means that the circular saw was overloaded briefly, or the overheating prevention cut-out has been activated. To solve this, release the control switch and then press it again. Also, allow the circular saw to cool down and clean the air vents.
Why does the running speed of my Hilti SCW 22-A suddenly drop?
A sudden drop in the running speed of your Hilti Saw can occur if the battery is discharged; in this case, charge the battery. Alternatively, you might be applying too much pressure. Try reducing the pressure and switch the product back on.
What does it mean when 4 LEDs blink on my Hilti SCW 22-A?
If you see 4 LEDs blinking on your Hilti Saw, it could mean one of two things: either the saw was briefly overloaded (in which case you should release the control switch and then press it again), or the overheating prevention cut-out has been activated. If it's the latter, allow the circular saw to cool down and clean the air vents.
Why is my Hilti SCW 22-A Saw or battery getting very hot?
If your Hilti Saw or its battery gets very hot, it could be due to an electrical fault. Immediately switch off the circular saw, remove the battery, and keep it under observation. Allow the battery to cool down. Alternatively, the product may be overloaded; select a tool that is suitable for its intended use.
Why is 1 LED blinking on my Hilti Saw?
If 1 LED is blinking on your Hilti Saw, the battery may be discharged, so try charging it. It could also indicate that the battery is either too hot or too cold. In this case, bring the battery to the correct ambient temperature.
Why does the battery of my Hilti SCW 22-A Saw run down quickly?
If the battery on your Hilti Saw is running down more quickly than usual, it may be because the battery condition is not optimal. Consider replacing the battery.
Why doesn't the battery engage with a 'double click' on my Hilti SCW 22-A Saw?
If the battery does not engage with an audible "double click" on your Hilti Saw, clean the retaining lugs and refit the battery. The retaining lugs on the battery are probably dirty.
Why is there no suction power in my Hilti SCW 22-A?
If there is no suction power or reduced suction power in your Hilti Saw, the chip ejector channel is blocked. Clean the chip / dust channel to restore suction.
How to fix Hilti SCW 22-A when LEDs indicate nothing?
If the LEDs indicate nothing, make sure that the battery is fully inserted. If it is not, insert the battery. Also, the battery might be discharged, so charge the battery. Finally, the battery might be too hot or too cold. In that case, bring the battery to the correct ambient temperature.
Why is there no or reduced suction power in my Hilti SCW 22-A Saw?
If you're experiencing no or reduced suction power with your Hilti Saw, the chip ejector channel might be blocked. Clean the chip / dust channel to resolve this.
Explains the meaning of DANGER, WARNING, CAUTION, and NOTE symbols.
Specifies the intended use of the cordless circular saw and its limitations.
Provides technical specifications for the SCW 22-A cordless circular saw.
Covers general safety warnings applicable to all power tools for safe operation.
Presents safety rules specifically for operating saws, including cutting procedures and kickback.
Offers further general safety advice, including personal safety and workplace considerations.
Provides step-by-step instructions for removing and fitting saw blades.
General| Blade diameter | 165 mm |
|---|---|
| Idle speed (max) | 4000 RPM |
| Cutting depth (45º) | 42 mm |
| Cutting depth (90º) | 57 mm |
| Sound pressure level | 93 dB |
| Vibration level (wood cutting) | 1.2 m/s² |
| Product color | Black, Red |
| Country of origin | Germany |
| Dust extraction port | Yes |
| Power source | Battery |
| Diamond disc | - |
| Battery included | No |
| Quantity per shipping (inner) case | 1 pc(s) |
Weight and Dimensions| Package depth | 898 mm |
|---|---|
| Package width | 5400 mm |
| Package height | 2000 mm |
| Package weight | 1345 g |
To Next Page
