Why does the drive spindle not rotate on my Hilti Power Tool?
The drive spindle on your Hilti Power Tool might not rotate because the permissible operating temperature of the rotary hammer’s electronics has been exceeded; allow the rotary hammer to cool down. Alternatively, the battery may be discharged, so try changing the battery and charging the empty one.
Why is there no hammering action on my Hilti Power Tool?
There could be several reasons why your Hilti Power Tool has no hammering action: * The rotary hammer may be too cold. Try bringing the tip of the drill bit into contact with the working surface, switch the rotary hammer on and allow it to run. Repeat if necessary. * The function selector switch might be set to “Drilling without hammering”. Set the function selector switch to “Hammer drilling”. * The rotary hammer could be set to reverse rotation. Move the forward / reverse selector switch to the “Forward” position.
Why is my Hilti Rotary Hammer not hammering?
If your Hilti Rotary Hammer isn't hammering, there could be a few reasons: * The rotary hammer might be too cold. Try bringing the tip of the drill bit into contact with the working surface, switch the rotary hammer on and allow it to run. If necessary, repeat the procedure until the hammering mechanism begins to operate. * The function selector switch may be set to “Drilling without hammering”. Ensure it is set to “Hammer drilling”. * The rotary hammer might have been set to reverse rotation. Switch it to the “Forward” position.
What to do if the battery does not engage with an audible "double click" in my Hilti TE 4-A22 Rotary Hammer?
If the battery does not engage with an audible "double click" in your Hilti Rotary Hammer, it is possible that the retaining lugs on the battery are dirty. Clean the retaining lugs and refit the battery.
What to do if LEDs indicate nothing on my Hilti TE 4-A22 Rotary Hammer?
If the LEDs indicate nothing on your Hilti Rotary Hammer, it could be due to the following reasons: * The battery is not fully inserted. Push the battery in until it engages with a double click. * The battery is discharged. Change the battery and charge the empty battery.
What to do if 1 LED blinks on Hilti TE 4-A22?
If 1 LED blinks on your Hilti Rotary Hammer, it could mean that the battery is discharged. Change the battery and charge the empty battery. Alternatively, the battery might be too hot or too cold. Bring the battery to the recommended working temperature.
What to do if the insert tool of Hilti Rotary Hammer can’t be released?
If the insert tool of your Hilti Rotary Hammer can’t be released, it might be because the chuck is not pulled back fully. Pull the chuck back as far as it will go and remove the accessory tool.
What to do if 4 LEDs blink on my Hilti TE 4-A22 Rotary Hammer?
If 4 LEDs blink on your Hilti Rotary Hammer, it indicates that the rotary hammer has been overloaded briefly. Release the control switch and then press it again.
Why does the battery of my Hilti TE 4-A22 Rotary Hammer run down quickly?
If the battery of your Hilti Rotary Hammer runs down more quickly than usual, it could be due to a very low ambient temperature. Allow the battery to warm up slowly to room temperature.
Why is my Hilti TE 4-A22 control switch locked?
If the control switch of your Hilti Rotary Hammer can’t be pressed, i.e. the switch is locked, it's likely because the forward / reverse switch is in the middle position. Push the forward / reverse switch to the right or left to unlock it.
General| Voltage | 21.6 V |
|---|---|
| Tool Chuck Type | SDS-Plus |
| Number of Gears | 1 |
| Drilling Mode | Hammer drilling, Drilling only |
| Reversing Switch | Yes |
| Battery Type | Li-ion |
| Max Drilling Diameter (Wood) | 20 mm |
| Max Drilling Diameter (Steel) | 13 mm |
| Tool Holder | SDS-Plus |
| Hammer Drilling Diameter Range | 4 - 18 mm |
| No-load Impacts Per Minute | 0 - 5200 ipm |
Guidance on reading and using the manual for safe operation.
Defines signal words, documentation symbols, and illustration symbols.
Details on the product, serial number, and declaration of conformity.
Statement of compliance with directives and standards.
Essential safety advice for operating power tools, including work area and electrical safety.
Guidelines for operator safety, including protective equipment and situational awareness.
Instructions for safe operation, maintenance, and storage of the tool.
Guidelines for handling, charging, and storing lithium-ion batteries safely.
Specific safety precautions for the rotary hammer, covering personal, electrical, and tool use.
Identifies and illustrates the main parts and controls of the rotary hammer.
Specifies the designed applications for the rotary hammer.
Explains how to check the charge status of the lithium-ion battery.
Lists the components included with the rotary hammer.
Provides key technical specifications for the rotary hammer.
Details measured noise and vibration levels for the tool.
Steps to prepare the work area and the tool before operation.
Instructions for attaching and positioning the side handle.
Guide on how to insert the battery into the tool correctly.
Steps for safely detaching the battery from the tool.
Instructions for inserting and securing drill bits or other accessories.
Steps for safely detaching accessories from the tool.
Guide on how to attach the depth gauge for controlled drilling depth.
Overview of different operational modes and settings like drilling and hammer drilling.
Instructions for cleaning and maintaining the tool and its batteries.
Specific instructions for cleaning the dust shield and sealing lip.
Guidelines for safely transporting and storing the cordless tool and batteries.
Advice on what to do when encountering issues, including contacting service.
Lists common malfunctions and their solutions.
Addresses issues that occur when the tool is operating but malfunctioning.
Instructions for environmentally responsible disposal of batteries.
To Next Page
