Hitachi L700 Series

Index
Index - 2
function mode ..................................................... 4-7
fuzzy ........................................................ 4-32, 4-83
FW ............................................................... 2-7, 4-8
FWR ................................................................. 4-72
H
H ................................................................ 2-8, 2-22
heat sink overheat warning ...................... 4-62, 4-71
heat sink temperature monitoring ....................... 4-4
high-torque multi-motor operation ..................... 4-95
I
initial screen...................................................... 4-81
initialization ....................................................... 4-78
input terminal a/b selection ....................... 4-48,4-63
input terminal response time............................. 4-71
inspection .................................................... 1-1, 6-1
instantaneous power failure/
under-voltage trip alarm enable ......... 4-33, 4-35
instantaneous power failure or
undervoltage ............................................... 4-33
intelligent input terminal ............................. 2-8, 4-47
intelligent input terminal status ........................... 4-2
intelligent output terminal ........................... 2-9, 4-62
intelligent output terminal status ......................... 4-2
internal DC braking ........................................... 4-20
inverter ready signal ......................................... 4-72
IP ...................................................................... 4-35
IRDY ................................................................. 4-72
J
JG ..................................................................... 4-50
jogging .............................................................. 4-50
jump (center) frequency .................................... 4-25
J300 .................................................................. 4-86
K
Keypad Run key routing ..................................... 4-7
KHC .................................................................... 4-3
L
L ................................................................ 2-8, 2-20
LAC ......................................................... 4-10, 4-32
LAD .................................................................. 4-10
life-check monitoring .................................. 4-4, 4-70
LOC .................................................................. 4-72
LOG1, LOG2, LOG3, LOG4, LOG5, LOG6 ...... 4-69
logical output signal operation .......................... 4-69
low-current indication signal ............................. 4-72
M
main circuit terminal ............................................ 2-8
main circuit wiring ............................................. 2-20
maintenance and inspection ............................... 6-1
major failure signal ........................................... 4-73
maximum frequency ......................................... 4-11
manual torque boost ......................................... 4-18
MI1, MI2, MI3, MI4, MI5, MI6, MI7, MI8 ............ 4-48
MO1, MO2, MO3, MI4, MO5, MO6 ................... 4-62
modbus RTU .................................................. 4-114
MJA .................................................................. 4-73
monitor mode .............................................. 4-1, 8-1
motor constant ........................................ 4-86, 4-89
motor temperature monitoring ............................ 4-4
multispeed 4 setting ......................................... 4-48
multistage speed/position
determination time ............................................ 4-49
N
NDc .................................................................. 4-70
no ..................................................................... 4-48
NO/NC .................................................... 4-48, 4-63
nonstop deceleration at instantaneous
power failure ............................................... 4-84
O
O ............................................................... 2-8, 2-20
O2 .................................................... 2-8, 2-20, 4-12
O2Dc ................................................................ 4-74
OD ........................................................... 4-28, 4-29
Odc .................................................................. 4-74
offline auto-tuning ............................................. 4-86
OHF ................................................................. 4-71
OI .............................................................. 2-8, 2-20
OIDc ................................................................. 4-74
OL, OL2 ........................................................... 4-41
OLR .................................................................. 4-40
online auto-tuning ............................................. 4-88
ONT ................................................................. 4-66
OPE ................................................... 3-4, 4-8, 4-52
operating methods ............................................. 3-1
operation after option error ............................... 4-82
operation frequency ......................................... 4-13
operation mode ................................................ 4-33
operation time over signal
(RNT)/plug-in time over signal
(ONT) ................................................ 4-61, 4-66
operator ................................................... 4-13, 4-69
OTQ ................................................................. 4-67
output current monitoring ................................... 4-1
output frequency monitoring ............................... 4-1
output frequency setting ..................................... 4-7
output signal delay/hold ................................... 4-75
output voltage monitoring ................................... 4-3
overcurrent restraint ......................................... 4-42
overload notice advance signal ............... 4-40, 4-41
overload restriction ........................................... 4-40
overtorque ........................................................ 4-67
P
P/PI switching ................................................... 4-60
P24 ............................................................ 2-8, 2-20
PCC ................................................................. 4-61
PCLR ............................................................... 4-96
PCNT ........................................................ 4-5, 4-61
phase loss input .............................................. 4-36
phase loss input protection ............................. 4-36
PID ................................................................... 4-26
PIDC ................................................................ 4-29
power monitoring ................................................ 4-3
PPI ................................................................... 4-59
process variable (PV), PID feedback
monitoring ............................................ 4-1, 4-29
program counter ................................................. 4-4