How to fix Honeywell Barcode Reader that scans, but the data is not correct?
If the scanned data is incorrect, ensure that the proper PC type (AT or PS2) is selected. Also, verify the correct country code and data formatting are selected, and adjust the intercharacter delay. The configuration may not be correct.
Why Honeywell 7820 Solaris shows alpha characters as lower case?
If alpha characters show as lower case, enable the Caps Lock detect setting of the scanner to detect whether the PC is operating in Caps Lock. This issue occurs because the computer is in Caps Lock mode.
What to do if Honeywell Barcode Reader powers up OK but does not communicate properly to the host?
If the Honeywell Barcode Reader powers up OK and scans OK but does not communicate properly to the host, check to make sure that the baud rate and parity of the scanner and the communication port match and the program is looking for “RS232" data. The com port at the host may not be working or configured properly.
Why Honeywell Barcode Reader beeps at some bar codes and not others?
The Honeywell Barcode Reader might beep for some bar codes and not for others of the same symbology because of several reasons: * The bar code may have been printed incorrectly; check for check digit, character, or border problems. * The scanner is not configured correctly for this type of bar code; check if check digits are set properly. * The minimum symbol length setting does not work with the bar code; check if the correct minimum symbol length is set.
What to do if Honeywell Barcode Reader is not transmitting each character?
If the Honeywell Barcode Reader is not transmitting each character, increase the interscan code delay setting and adjust whether the F0 break is transmitted. It may be necessary to try this in both settings. The configuration may not be correct.
What to do if Honeywell Barcode Reader scans a bar code, but locks up after the first scan?
If the Honeywell Barcode Reader scans a bar code but locks up after the first scan (blue LED stays off), it may be configured to support some form of host handshaking but isn't receiving the signal. If the scanner is set up for ACK/NAK, RTS/CTS, XON/XOFF, or D/E, verify that the host cable and host are properly supporting the handshaking.
Why Honeywell Barcode Reader powers up, but does not scan and/or beep?
If the Honeywell Barcode Reader powers up but doesn't scan or beep, it could be due to a couple of reasons. First, ensure that the symbology you are scanning is enabled. By default, UPC/EAN, Code 39, Interleaved 2 of 5, Code 93, Code 128, and Codabar are enabled. Secondly, the scanner might be configured for a character length lock, or a minimum length that the scanned bar code does not meet. Verify that the bar code meets the configured criteria, as the scanner defaults to a minimum of 4 characters for Non-UPC/EAN codes.
What to do if my Honeywell 7820 Solaris scans but the data transmitted is incorrect?
If the data transmitted to the host is incorrect, verify that the scanner’s data format matches the format required by the host and that the scanner is connected to the proper host port. The scanner’s data format may not match the host system requirements.
How to fix Honeywell 7820 Solaris that is not transmitting each character?
If the Honeywell Barcode Reader is not transmitting each character, increase the intercharacter delay setting and adjust whether the F0 break is transmitted (KBW Interface ONLY). It may be necessary to try this in both settings. The configuration may not be correct.
General| Connectivity | RS-232, USB, Keyboard Wedge |
|---|---|
| Storage Temperature | -40°C to 60°C (-40°F to 140°F) |
| Light Source | 650 nm visible laser diode |
| Humidity | 5% to 95% (non-condensing) |
| Input Voltage | 5V DC ±5% |
| Electrical Safety | UL, CSA, EN60950 |
| EMC | FCC Part 15, ICES-003, EN55022 Class B |
Details the 7820 Solaris scanner's features, productivity benefits, and suitability for retail environments.
Provides instructions for connecting the 7820 scanner using specific interfaces like Keyboard Wedge, USB, RS232, RS485.
Details common failure modes indicated by LED and beep combinations on the 7820 scanner.
Explains the green single-digit error code display for diagnosing scanner issues.
A guide to identify and resolve common symptoms and issues with the 7820 scanner across all interfaces.
Explains the three configuration modes for the 7820 scanner: Bar Codes, MetroSet2, and Serial Programming.
Provides step-by-step instructions for upgrading the firmware of the 7820 scanner using MetroSet2 software.
Covers safety information related to ITE Equipment, Laser Class 1, and LED classifications.
Outlines the warranty terms, conditions, exclusions, and duration for the 7820 Solaris scanner and accessories.
To Next Page