Honeywell SEC-H-600 - WEBs-AX Security Enclosure

SEC-H-600 SECURITY CONTROLLER
95-7759—07 4
WEBs-AX Security Enclosure
For a UL Listed system, the Security Controller, plus all expansion modules, must be mounted in one or more WEBs-AX Security
Enclosures. These enclosures meet the UL 294 listing, have a pre-mounted DIN rail (or rails), and include a door with a key lock
and tamper switch. Two models have an integral 30W 15Vdc power supply that powers the SEC-H-600 controller and/or the
expansion modules inside the enclosure.
Fig. 2. Security Controller must be mounted in WEBs-AX Security Enclosure (model SEC-ENC-H-1 or SEC-ENC-H-2).
As shown in Fig. 2, there are 3 different-sized WEBs-AX Security Enclosures available, including these models:
SEC-ENC-H-1: (Medium) For the Security Controller in the smallest job configuration, or where additional expansion modules
are located remotely (in other Security Enclosures). It provides a single DIN rail and an integral 30W 15Vdc power supply to
power the controller, or up to two SEC-H-R2Rs, or one SEC-H-RIO. The controller (or modules) plug directly into the power
supply, see Fig. 2. Brackets at the bottom of the enclosure secure one or two rechargeable sealed lead-acid backup batteries
(batteries used only if a Security Controller is housed). In larger systems, more Security Enclosures can be used to house
additional expansion modules.
Another medium-sized enclosure without an integral power supply is also available, model SEC-ENC-H-1NP. It is used for
expansion modules only (not the Security Controller), and it has room for one additional SEC-H-R2R module.
SEC-ENC-H-2: (Large) Used for the Security Controller in larger job configurations, it provides a DIN rail mount and an integral
30W 15Vdc power supply for the controller, and a second DIN rail for expansion modules—for example, up to four (4) SEC-H-
R2R modules. The SEC-H-600 controller plugs directly into the power supply, see Fig. 2. A supplied six-conductor wiring harness
(not shown) provides power and RS-485 communications to expansion modules mounted on the lower DIN rail. Brackets at the
bottom of the enclosure secure one or two rechargeable sealed lead-acid backup batteries (backup batteries used only if
enclosure houses an Security Controller). In larger systems, more Security Enclosures can be used to house additional modules.
Another large-sized enclosure without the integral power supply is also available, model SEC-ENC-H-2NP. It is used for
expansion modules only (not the Security Controller), and it has room for one additional SEC-H-R2R module.
Battery Space
35mm DIN Rail
12V
Backup
Battery
Integral
30W
15Vdc
PS
Security
Controller
Only application
Larger System Configuration
SEC-ENC-H-1 SEC-ENC-H-2
AC Line
Input
120-
240Vac
15Vdc
output
Battery Space
35mm DIN Rails (2)
Integral
30W
15Vdc
PS
15Vdc
output
Battery
Space
Integral
30W
15Vdc
PS
SEC-H-RIO
(2)
SEC-H-R2R
Integral
30W
15Vdc
PS
12V Backup
Battery
12V Backup
Battery
SEC-ENC-H-3
Minimal System Configuration
SEC-H-R2R
Integral
30W
15Vdc
PS
Unused
Space
Unused
Space
(2)
SEC-H-R2R
NOTE: In larger systems, additional
enclosures can be used for modules only
(no Security Controller), where backup
batteries are not used. At right an SEC-
ENC-H-1 is used this way.
SEC-ENC-H-1
35mm
DIN Rail
NOTE: Interconnecting
cables not shown.
Security
Controller