Hoymiles HAT-5.0HV-EUG1 User Manual (English)

Other manuals for Hoymiles HAT-5.0HV-EUG1

Questions and Answers:

B
brendaallenAug 21, 2025
What to do if my Hoymiles HAT-5.0HV-EUG1 Inverter shows Grid Overvoltage?
- S
  Stephanie ShawAug 22, 2025
  If your Hoymiles Inverter frequently shows a Grid Overvoltage alarm, it means the grid voltage is higher than the permissible range. While the inverter typically reconnects after the grid recovers, you should: 1. Ensure the inverter's safety country setting is correct. 2. Confirm your area's grid voltage is stable and within the normal range. 3. Verify the AC cable's cross-sectional area meets the requirement. If the alarm persists, further assistance may be needed.
D
David WhiteAug 23, 2025
What to do if my Hoymiles HAT-5.0HV-EUG1 Inverter shows No Grid error?
- E
  Erin WashingtonAug 23, 2025
  If your Hoymiles Inverter frequently alarms 'No Grid', it indicates the inverter isn't detecting a grid connection. While the inverter usually reconnects automatically, check the following: 1. Confirm the grid supply is reliable. 2. Ensure the AC cable is firmly in place. 3. Verify the AC cable is correctly connected. 4. Check if the AC circuit breaker is disconnected. If the problem continues, further investigation may be needed.
N
Nancy MclaughlinAug 25, 2025
What to do if my Hoymiles HAT-5.0HV-EUG1 Inverter shows Grid Undervoltage?
- J
  Jeffrey SanfordAug 25, 2025
  If your Hoymiles Inverter frequently shows a Grid Undervoltage alarm, it means the grid voltage is lower than the permissible range. While the inverter will usually reconnect after the grid recovers, you should: 1. Make sure the safety country of the inverter is set correctly. 2. Make sure that the grid voltage in your area is stable and within the normal range. 3. Check whether the AC cable is firmly in place. If the alarm persists, further assistance may be needed.
C
Clayton WoodsAug 26, 2025
Why does my Hoymiles HAT-5.0HV-EUG1 Inverter show a Residual Current Fault?
- K
  Kristi MartinAug 27, 2025
  A Residual Current Fault on your Hoymiles Inverter indicates that the residual leakage current is too high. This can be due to a couple of reasons: * High ambient humidity may cause this alarm; the inverter will reconnect once conditions improve. * If the environment is normal, verify that the AC and DC cables are well insulated. If the alarm continues, further diagnostics might be necessary.
L
Lindsay FernandezAug 27, 2025
What to do if Hoymiles Inverter displays Grid Overfrequency?
- M
  Mr. Logan Murphy MDAug 27, 2025
  If your Hoymiles Inverter frequently shows a Grid Overfrequency alarm, it means the grid frequency is higher than the permissible range. While the inverter typically reconnects after the grid recovers, you should: 1. Make sure the safety country of the inverter is set correctly. 2. Make sure that the grid frequency in your area is stable and within the normal range. If the alarm persists, further assistance may be needed.
D
Dalton WigginsAug 29, 2025
What to do if my Hoymiles HAT-5.0HV-EUG1 Inverter indicates a PV Reverse Connection?
- A
  Anthony FletcherAug 29, 2025
  If your Hoymiles Inverter displays a PV Reverse Connection error, it means the PV strings are connected with reverse polarity. To resolve this: 1. Check if the corresponding string has reverse polarity. If so, disconnect the DC switch and adjust the polarity when the string current drops below 0.5 A. If the alarm persists, further assistance may be needed.
L
lhebertAug 30, 2025
How to fix Over Temperature error on Hoymiles Inverter?
- M
  Melinda MitchellAug 31, 2025
  If your Hoymiles Inverter shows an Over Temperature alarm, it means the internal temperature is too high. To address this: 1. Ensure the installation complies with the instructions from User Manual. 2. Check if a Fan Fault alarm is also present; if so, replace the faulty fan. If the alarm persists, further assistance may be needed.
K
Kathryn WoodSep 1, 2025
What causes a PV Undervoltage error on a Hoymiles Inverter and how to fix it?
- P
  Peter PottsSep 1, 2025
  A PV Undervoltage error on your Hoymiles Inverter indicates that the PV voltage is lower than the permissible range. Here's what you can do: 1. Ensure the DC cable is firmly in place. 2. Check for any shading on the PV module and remove it; also, ensure the PV module is clean. 3. Inspect the PV module for signs of abnormal aging. If the alarm persists, further assistance may be needed.
M
Michael WadeSep 2, 2025
What causes Isolation Fault on Hoymiles HAT-5.0HV-EUG1 Inverter?
- B
  Billy HallSep 2, 2025
  An Isolation Fault on your Hoymiles Inverter means the insulation impedance of the PV string to the ground is too low. To troubleshoot: 1. Use a multimeter to check if the resistance between the earth and the inverter frame is close to zero; ensure the connection is good. 2. High humidity can cause this; try restarting the inverter, or check again when the weather is better. 3. Check the resistance to ground from the PV module/cable, and correct any short circuits or damaged insulation. If the alarm persists, further assistance may be needed.
J
johnhamiltonSep 4, 2025
What to do if my Hoymiles HAT-5.0HV-EUG1 displays PV Overvoltage?
- K
  Kerry GreenSep 4, 2025
  If your Hoymiles Inverter displays a PV Overvoltage error, it means the PV voltage is higher than the permissible range. You can: 1. Check the specification and numbers of corresponding string PV modules. If the alarm persists, further assistance may be needed.

Hoymiles HAT-5.0HV-EUG1 Specifications

General

Model	HAT-5.0HV-EUG1
Category	Inverter
Rated Power	5000 W
Rated AC Output Power	5000 W
Nominal AC Voltage	230 V
Max. Output Current	22 A
Nominal Frequency	50/60 Hz
THDi	<3%
Max Efficiency	98.4%
Efficiency	98.0%
MPPT Efficiency	99.9%
Number of MPPTs	2
Operating Temperature Range	-25°C to +60°C
Cooling	Natural Convection
Protection Level	IP65
Max. AC Output Power	5500 VA
Power Factor	>0.99
Communication	Wi-Fi, Ethernet, RS485