EasyManua.ls Logo

HP 250 - Changing Roll Paper

HP 250
180 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Graphics
Devices
Four
and
Eight
Pen
Plotters:
1.
Disable
the
plotter
by
turning
on
the
STANDBY
lamp.
2.
Push
the
CHART
LOAD
pushbutton
to
turn
on
the
CHART LOAD
lamp.
The
OUT
OF
LIMIT
light
should
also
go
on
steadily,
and
the
pen
holder
is
moved
to
the
upper
right
corner
of
the
platen.
3.
Remove
old
paper.
4.
Place
sheet
of
paper
on
the
platen
so
that
the
lower
edge
is
under
the
lips
of
the
nylon
paper
stop.
Then
move
the
paper
to
the
left
so
that
the
paper
is
snug
against
the
left
paper
stop.
(The
left
paper
stop
may
be
depressed.
If
so,
raise
the
lower
one
by
pushing
with
a
pencil
on
the
upper
one.)
See
the
figure
below.
For
smaller
sheets
of
paper
(e.g.,
ISO
A4),
place
the
long
edge
of
the
paper
against
the
left
edge
of
the
plotter.
5.
Press
the
CHART
HOLD
pushbutton
and
smooth
out
any
ripples
using
the
back
of
your
hand
with
left-to-right
motion.
The
CHART
LOAD
lamp
should
go
off.
6.
When
ready
to
resume
plotting,
push
the
ON
LINE
pushbutton
twice.
The
ON
LINE
lamp
should
blink,
and
the
STANDBY
lamp
should
turn
off.
Changing Roll Paper
The
Sand
T
plotter
models
have
automatic
chart
advance
capability.
You
may
use
these
plotters
either
with
a
roll
of
paper
or
in
the
single
sheet
mode
used
with
the
other
plotters.
See
the
Operating
and
Programming
Manual
supplied
with
your
plotter
for
detailed
instructions
on
changing
a
roll
of
paper.
7-8
Graphics
Devices
Four
and
Eight
Pen
Plotters:
1.
Disable
the
plotter
by
turning
on
the
STANDBY
lamp.
2.
Push
the
CHART
LOAD
pushbutton
to
turn
on
the
CHART LOAD
lamp.
The
OUT
OF
LIMIT
light
should
also
go
on
steadily,
and
the
pen
holder
is
moved
to
the
upper
right
corner
of
the
platen.
3.
Remove
old
paper.
4.
Place
sheet
of
paper
on
the
platen
so
that
the
lower
edge
is
under
the
lips
of
the
nylon
paper
stop.
Then
move
the
paper
to
the
left
so
that
the
paper
is
snug
against
the
left
paper
stop.
(The
left
paper
stop
may
be
depressed.
If
so,
raise
the
lower
one
by
pushing
with
a
pencil
on
the
upper
one.)
See
the
figure
below.
For
smaller
sheets
of
paper
(e.g.,
ISO
A4),
place
the
long
edge
of
the
paper
against
the
left
edge
of
the
plotter.
5.
Press
the
CHART
HOLD
pushbutton
and
smooth
out
any
ripples
using
the
back
of
your
hand
with
left-to-right
motion.
The
CHART
LOAD
lamp
should
go
off.
6.
When
ready
to
resume
plotting,
push
the
ON
LINE
pushbutton
twice.
The
ON
LINE
lamp
should
blink,
and
the
STANDBY
lamp
should
turn
off.
Changing Roll Paper
The
Sand
T
plotter
models
have
automatic
chart
advance
capability.
You
may
use
these
plotters
either
with
a
roll
of
paper
or
in
the
single
sheet
mode
used
with
the
other
plotters.
See
the
Operating
and
Programming
Manual
supplied
with
your
plotter
for
detailed
instructions
on
changing
a
roll
of
paper.
7-8

Table of Contents

Related product manuals