EasyManua.ls Logo

HP 250 - Loading from the HP 7908,7911, or 7912 Disc

HP 250
180 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
System
Start-up
5.
If
no
problem
occurs,
a
message
in
the
form:
SYSTEM
LOADING
foIl
owe
d
by:
LOADING
DROMS
is
shown.
The
message
remains
on
the
screen
for
about
30
seconds.
When
the
loading
process
is
complete,
a
blinking
underscore,
known
as
the
cursor,
is
displayed.
If
the
message:
The
"SYSTEM"
file
was
not
found
appears
on
the
screen
while
loading
the
tape
either
you
did
not
insert
the
cartridge
properly
or
the
tape
you
used
did
not
have
the
system
software
on
it.
You
should
turn
the
key
to
the
off
position
(0),
ensure
that
the
tape
cartridge
in
the
drive
is
lab-
eled
SYSTEM,
and
then
repeat
the
loading
procedure.
When
the
system
has
been
properly
loaded,
you
may
remove
the
tape
cartridge
labeled
SYSTEM
from
the
drive.
Press
the
UNLOAD
key
on
the
drive.
The
BUSY
light
will
flash.
When
the
tape
cartridge
is
ready
to
be
removed,
a
buzzer
sounds.
Pull
the
lever
gently
to
the
right
and
remove
the
cartridge
from
the
drive.
If
the
result
of
the
self-test
is
an
error
message
or
the
system
failed
to
power
on,
consult
the
section
titled
"In
Case
of
Difficulty".
Loading from the
HP
7908,7911,
or
7912 Disc
After
the
operating
system
has
been
copied
to
an
HP
7908,
7911,
or
7912
disc,
you
can
start
your
HP
250
directly
from
the
disc.
1.
Turn
the
power
switch
of
the
Integrated
Storage
Product
to
the
ON
(1)
position.
Ensure
that
no
storage
medium
labeled
SYSTEM
is
in
any
other
drive.
2.
Insert
the
key
of
the
HP
250
into
the
lock
and
turn
it
clock-
wise
to
position
1.
3.
A
system
self-test
is
automatically
performed
when
you
turn
the
power
on.
As
the
test
is
performed,
a
list
of
system
components
is
displayed.
If
any
component
fails,
the
system
is
not
operable;
consult
the
chapter
"In
Case
of
Difficulty"
if
this
occurs.
Rev.
1/82
2-3
System
Start-up
5.
If
no
problem
occurs,
a
message
in
the
form:
SYSTEM
LOADING
foIl
owe
d
by:
LOADING
DROMS
is
shown.
The
message
remains
on
the
screen
for
about
30
seconds.
When
the
loading
process
is
complete,
a
blinking
underscore,
known
as
the
cursor,
is
displayed.
If
the
message:
The
"SYSTEM"
file
was
not
found
appears
on
the
screen
while
loading
the
tape
either
you
did
not
insert
the
cartridge
properly
or
the
tape
you
used
did
not
have
the
system
software
on
it.
You
should
turn
the
key
to
the
off
position
(0),
ensure
that
the
tape
cartridge
in
the
drive
is
lab-
eled
SYSTEM,
and
then
repeat
the
loading
procedure.
When
the
system
has
been
properly
loaded,
you
may
remove
the
tape
cartridge
labeled
SYSTEM
from
the
drive.
Press
the
UNLOAD
key
on
the
drive.
The
BUSY
light
will
flash.
When
the
tape
cartridge
is
ready
to
be
removed,
a
buzzer
sounds.
Pull
the
lever
gently
to
the
right
and
remove
the
cartridge
from
the
drive.
If
the
result
of
the
self-test
is
an
error
message
or
the
system
failed
to
power
on,
consult
the
section
titled
"In
Case
of
Difficulty".
Loading from the
HP
7908,7911,
or
7912 Disc
After
the
operating
system
has
been
copied
to
an
HP
7908,
7911,
or
7912
disc,
you
can
start
your
HP
250
directly
from
the
disc.
1.
Turn
the
power
switch
of
the
Integrated
Storage
Product
to
the
ON
(1)
position.
Ensure
that
no
storage
medium
labeled
SYSTEM
is
in
any
other
drive.
2.
Insert
the
key
of
the
HP
250
into
the
lock
and
turn
it
clock-
wise
to
position
1.
3.
A
system
self-test
is
automatically
performed
when
you
turn
the
power
on.
As
the
test
is
performed,
a
list
of
system
components
is
displayed.
If
any
component
fails,
the
system
is
not
operable;
consult
the
chapter
"In
Case
of
Difficulty"
if
this
occurs.
Rev.
1/82
2-3

Table of Contents

Related product manuals