HP 54501A - Page 11

Table 1-1 . HP 54507A
Specifications and Characteristics
HP
54501A GENERAL
INFORMATION
SPECIFICATIONS
BANDWIDTH :
dc-coupled
Repetitive : do to 100 MHz (-3 dB)
Single Shot : do to 1 MHz
(Based on
10 points
per period
of
input
signal .)
ac-coupled
Repetitive : 10 Hz to 100 MHz (-3dB)
Single Shot : 10 Hz to 1 MHz
(Based on 10 points per period of input signal .)
RISETIME : 3 .5 ns
(Calculated from : Risetime = 0 .35/Bandwidth .)
NUMBER OF CHANNELS : 4 (2+2)
Channels 2 and 3 are limited attenuatoi
inputs, optimized for digital signals .
SIMULTANEOUS
CHANNELS
: 2+2
Channels 1 or 2 simultaneous with 3 or 4 . With
more than two channels, the other channels are
acquired alternately in pairs .
VERTICAL SENSITIVITY
Maximum
: 5
mV/div
Minimum : 5 V/div
VERTICAL GAIN ACCURACY (de) : ±1 .5%
MAX INPUT VOLTAGE : ±250 V DC+ peak ac (C10KHz)
OFFSET ACCURACY :
±2% of offset + 0
.2 X
(V/div) + .075
div/ ° C from
calibration temperature .
(For 5 mV/div range, ±2% of offset + 0 .4 X (V/div) +
+ 0 .15 div/ ° C from calibration temperature .)
VOLTAGE MEASUREMENT ACCURACY (single channel)
Single Cursor . Gain Accuracy + offset +
A/D resolution
Dual Cursor . Gain Accuracy + 2X AID resolution
TIME BASE RANGE
Minimum : 2 ns/div
Maximum : 5 s/div
TIME BASE ACCURACY : 0 .005%
DELAY t ACCURACY :
+-2% of (t/div) +- .005% of Delta t +-
1 ns
Delta t accuracy for dual-cursor, single-channel
measurement, or for channel-to-channel
measurement after visual time null calibration
has been done .
TRIGGER SENSITIVITY
5 mv/div :
dc-20 MHz

0 .1 X full-scale
20
MHz-100 MHz

0 .25 X full-scale
All other .
dc-20 MHz

0 .05 X full-scale
20 MHz-100 MHz

0 .125 X full-scale
CHARACTERISTICS
VERTICAL RESOLUTION :
±0 .4% - 6-bit
A/D
(Since expansion is used for 5 mV/div
range, A/D
resolution is 7 bits
[0 .8%] in that range .)
±0 .1% - 10
bits via HP-IB
(with
averaging)
MAXIMUM SAMPLE
RATE : 10 Msa/s
MEMORY DEPTH :
501 points (display)
1024 points (via HP-IB)
(For single-shot via HP-IB, maximum memory
depth is
501
points
.
For
2
ns/div time base range, memory depth
is 200 points . For 5 ns/div
time base range,
maximum memory depth via HP-113 is 501
points .)
INPUT RC (nominal)
: 1 MCI, 16 pF
INPUT COUPLING :

sc,
do
OFFSET RANGE :
Sensitivity Range

-

Available Offset
5 - 50 mV/div

±2V
0 .1 - 1 V/div

±20V
1 - 5 V/div

±200V
DYNAMIC RANGE : ±16 divisions from center
Operating range for do + peak AC input .
CHANNEL-TO-CHANNEL ISOLATION
:
(with channels at equal sensitivity)
40dB do to 20 MHz
30 dB

20 MHz to 100 MHz
MAXIMUM
TIMEBASERESOLUTION : 100 ps
DELAY RANGE (post trigger)
:
Time Base Setting

-

Available
Delay
50 ms- 5 s

40 X (s/div)
100/is - 20 ms

1 8
2ns - 50 Ps

-10,000 X (s/div)
DELAY RANGE (pretrigger) :
Time Base Setting

Delay
10 F1 .s - 5 s

-40 X (s/div)
20 ns - 5 /Is

-200 As
2 ns - 10 ns

-10,000 X (s/div)
TRIGGER PULSE WIDTH (minimum) : 7 ns
TRIGGER LEVEL RANGE : ±6 div from center
Specifications valid for temperature range ± 10 ° C calibration temperature with
8
averages
selected and channei(s) in sen-
sitivity range 1, 2, or 5 .