General Information
lbble
1-1.
Specijications
(5
of
6)
Model
8901B
RF Input
FREQUENCY RANGE:
150
kHz to
1300
MHz.
OPERATING LEVEL:
Frequency
Range
I
Maximum
I
Operating
level
I
Operating
level
Minimum
I
'lms
("peak)
Source
SWR
e4
I
150
kHz-650 MHz
12
mVrms
(-25
dBm)
I
Supplemental Characteristics:
TUNING:
Normal Mode:
Automatic and manual frequency
Track Mode:
Automatic and manual frequency entry,
f,
210
MHz.
Acquisition Time (automatic operation):
entry.
-I
.5
seconds.
INPUT IMPEDANCE:
50R
nominal.
MAXIMUM SAFE DC INPUT LEVEL:
5V.
General Specifications
TEMPERATURE:
Operating:
O°C
to
55OC.
Storage:
-55%
to
75OC.
REMOTE OPERATION:
HP-IB;
alI
functions except the
HP-IB COMPATIBILITY
(defined in
IEEE
488-1978):
line switch are remotely controllable.
SHI, AHI,
T5,
TEO.
L3,
LEO.
SRI,
RLI.
PPO.
DC1.
DT1,
CO,
El.
requirements
of
VDE
0871
(Level
B).
and
CISPR
publication
11.
200
VA maximum.
EMI:
Conducted and radiated interference
is
within the
POWER:
100.120,
220.
or
240V
(+5%.
-lO0/o):
48-66
Hz:
WEIGHT:
Net
23.4
kg.
(51.5
lb.);
Shipping 31.1 kg
(68.5
lb).
DIMENSIONS:
190
mm.
H
X
426
mm.
M'
X
551
mm.
D
HP SYSTEM I1 MODULE SIZE:
177.0
H
X
1
MLY
X
497.8
D.
(7.5"
X
16.8"
X
21.7").
HP
8901
B
Rear Panel Inputs/Outputs
Supplemental Characteristics:
FM OUTPUT:
10
kR
impedance,
-9V
to 6V into an open
circuit: -6V/MHz, dc coupled, 16 kHz bandwidth (one
,
pole).
AM OUTPUT:
10
kR impedance,
-4V
to
OV
into an open
circuit,
-8
mV/%, dc coupled, 16 kHz bandwidth (one
pole).
RECORDER OUTPUT:
DC
voltage proportional to the
measured results,
1
kR
impedance,
OV
to 4VfOr each
resolution range into an open circuit.
-27 dBm to
-3
dBm.
levels
(OV
to
>2.2V
into an open circuit). Available only
with Option
002
Ixlo-g/day internal reference.
10
MHz
REFERENCE INPUT15
>500R
impedance,
0.5Vpeak.lo.peak
minimum input level.
LO
INPUT (Option
003):
5OR
impedance,
-1.27
MHz
to
1301.5
MHz,
0
dBm nominal.
RF SWITCH REMOTE CONTROL OUTPUT:
Provides
output signals necessary to remotely control either an
HP
3331
1B/C Option
01
1
or
an HP 8761A RF switch.
FREQUENCY OFFSET MODE REMOTE CONTROL
OUTPUT:
TTL
high output if in frequency offset mode
(Special Function
27.1
or
27.3)
with an external
LO
frequency
>O,
TTL
low output for
all
other cases.
IF
OUTPUT:
50R
impedance,
150
kHz
to
2.5
MHz,
10
MHz REFERENCE OUTPUT:
50R
impedance,
TTL
'5~xternai reference
accuracy
affects
accuracy
ut
ail
iiie~asurements.
1-23
To Next Page
Loading...
