To Next PageTo Next Page
What to do if HP Storage port number is invalid?
If the port number specified is invalid or the cable isn't connected to the specified port on your HP Storage, delete the failed path. Check the specified port number and the cable connection, then retry.
How to troubleshoot HP StorageWorks P9000 Storage Communication Failed error?
If communication fails on your HP Storage, meaning the primary system connects to the secondary system but a logical communication timeout occurs, ensure that the secondary system port and network relay devices (cables, switches) are properly configured and functioning.
How to troubleshoot DATASET_ERROR_DSORG_NOT_SUPPORTED in HP Storage?
To troubleshoot the DATASET_ERROR_DSORG_NOT_SUPPORTED error, check the DO type using the MF-File list command in the FCU Help menu or the VTOC dump data on the mainframe host.
What causes DATASET_ERROR_VOLUME_DEFINED_READ_ONLY in HP Storage?
If you encounter the DATASET_ERROR_VOLUME_DEFINED_READ_ONLY error, ensure that the target dataset for an open-system write operation is on a 3390-3A/C volume.
How to fix missing LUN mapping information in HP StorageWorks P9000 mapping reports?
Missing LUN mapping information in the mapping reports can occur if read permission has not been assigned on corresponding OS device special files. Assign read permission to device special files to resolve this.
How to fix HP Storage initialization failed error?
If initialization fails on your HP Storage, which means the link initialization procedure for the secondary system failed, ensure that the cables between the primary and secondary systems are correctly connected. Verify the serial number (S/N) of the secondary system and the path parameters (primary system port, secondary system port, and controller ID). Also, confirm that the topology settings of the primary and secondary system ports are correct.
What to do if HP Storage port is rejected?
If the primary and secondary HP Storage systems reject a request for a logical path due to resource constraints, delete the failed path, as well as any unused paths and secondary systems. Remember that the primary system can connect to up to 64 secondary systems, each with up to eight paths. Ensure all ports on both systems are correctly configured. If necessary, connect to the secondary system to delete paths or reconfigure ports, then reconnect to the primary system before re-adding the path and secondary system.
How to resolve HP Storage Communication Time Out error?
If a communication timeout occurs between the primary and secondary HP Storage systems, ensure the secondary system is powered on and that NVS and cache are fully functional. Verify that all network relay devices are properly configured and functional. Delete the failed path, which may require adjusting the minimum paths setting or deleting the secondary system first. After deletion, re-add the path or secondary system using the Add Path or Add DKC dialog box.
What to do if HP Storage pair create operation resulted in a timeout error?
If a pair create or resync operation on your HP Storage results in a timeout error, and a SIM was generated due to a hardware failure, call HP Technical Support after the problem is solved, then retry Cnt Ac-J Z operations. If no SIM was generated, wait 5-6 minutes and check the pair status. If the status changed correctly, the operation completed after the timeout. If the status did not change, retry the operation during a lighter workload. If there is a communication error between the Remote Web Console and the SVP, consult the HP StorageWorks P9000 Remote Web Console User Guide.
How to fix HP Storage Remote Web Console when it hangs?
If the HP Storage Remote Web Console hangs or Cnt Ac-J Z operations malfunction, first ensure the issue isn't with your computer, Ethernet hardware, or software by restarting the computer. Verify that all Cnt Ac-J Z requirements are met, and that the primary/secondary systems and remote copy connections are powered on with operational NVS and cache. Double-check all entered values and parameters for accuracy in the Remote Web Console. Avoid using Performance Monitor during these operations.
General| RAID Support | RAID 0, 1, 5, 6, 10 |
|---|---|
| Interface | Fibre Channel, iSCSI, FCoE |
| Form Factor | Rack-mountable |
| Model | P9000 |
| Operating System Compatibility | Windows, Linux, VMware, HP-UX |
| Host Interface | Fibre Channel, iSCSI, FCoE |
| Drive Interface | SAS, SSD |
| Drive Types Supported | SSD, SAS |
| Redundancy | Redundant controllers, power supplies, and fans |
| Management Software | HP StorageWorks Command View |
