To Next Page
T
Thomas AdamsSep 7, 2025
What to do if hpmont HD5L-4T7P5 displays E0013 error?
- JJo MortonSep 7, 2025
If the hpmont Controller displays error E0013, which indicates soft start contactor failed, replace the contactor.
What to do if hpmont HD5L-4T7P5 displays E0013 error?
If the hpmont Controller displays error E0013, which indicates soft start contactor failed, replace the contactor.
What causes E0001 error on hpmont HD5L-4T7P5 and how to fix it?
The E0001 error on your hpmont Controller means Acc overcurrent. To resolve this, ensure that the HD5L and motor are properly connected, set the correct motor parameters, select a controller with a higher rating, and set proper Acc time and Dec time.
What to do if hpmont Controller displays E0017 error?
If the hpmont Controller displays error E0017, which indicates a controller overload, you can adjust the Acc time, adjust the V/f curve or torque boost, check the mains supply voltage, or use a controller with proper power rating.
Why did the soft start fail on my hpmont HD5L-4T7P5?
If the hpmont Controller indicates a 'Soft start failed' error, it could be due to a contactor fault or a fault in the control circuit. Replace the contactor.
What causes Braking unit fault in hpmont HD5L-4T7P5?
If the hpmont Controller reports a Braking unit fault, it indicates a circuit fault within the braking unit. Please seek technical support.
Why is there excessive speed deviation in hpmont HD5L-4T7P5?
If the hpmont Controller indicates excessive speed deviation, the possible causes are: a brake or contactor fault, PG pulse number fault, improper settings of F05.19 and F05.20, inadequate controller torque, or incorrect speed-loop PI parameter settings. To address this, consider the following: 1. Change the contactor 2. Set proper PG P/R 3. Correct the setting of F05.19 and F05.20 4. Select bigger capacity controller 5. Correctly set speed-loop PI parameter
What to do if hpmont HD5L-4T7P5 Controller displays E0024 error?
If the hpmont Controller displays error E0024, which indicates a fault of external equipment, check external equipment.
What to do if hpmont Controller displays E0028 error?
If the hpmont Controller displays error E0028, which indicates SCI communication timeout, check the connection.
What does Controlboard EEPROM faulty mean on hpmont HD5L-4T7P5 Controller?
If the hpmont Controller displays 'Controlboard EEPROM faulty', it means there is a memory circuit fault of control board EEPROM. Please contact the supplier for repairing.
Why hpmont HD5L-4T7P5 shows E0018 error?
The E0018 error on the hpmont Controller indicates excessive speed deviation. To fix it, change the contactor, set proper PG P/R, correct the setting of F05.19 - F05.20, select bigger capacity, and correctly set speed-loop PI parameter.
Details restrictions on output side connections, voltage, and input phase usage.
Lists detailed electrical, performance, characteristic, and protection specifications.
Provides a table of models, power ratings, input/output currents, and motor power.
Outlines essential safety precautions before and during controller installation.
Specifies environmental and spatial requirements for controller installation.
Lists critical safety precautions and guidelines for electrical wiring.
Covers terminal descriptions and wiring practices for the main power circuit.
Explains wiring precautions and general connections for the control circuit.
Provides guidelines for installation to meet EMC standards and reduce interference.
Defines the four modes for receiving run commands and setting speed.
Explains the five available running modes for the controller.
Provides step-by-step examples for setting parameters and managing user passwords.
Guides the user through the initial power-on and controller initialization process.
Outlines basic steps for system analysis, wiring, and parameter setup.
Provides a table listing fault codes, possible causes, and countermeasures.
Lists basic parameters with their attributes, default values, and ranges.
Lists parameters for parameter protection with their attributes and default values.
Lists start/stop parameters with their attributes and default values.
Lists acceleration/deceleration parameters with their attributes and default values.
Lists speed parameters with their attributes and default values.
Lists asynchronous motor parameters with their attributes and default values.
Lists speed-loop parameters for vector control with attributes and default values.
Lists synchronous motor parameters with their attributes and default values.
Lists PG (encoder) parameters with their attributes and default values.
Lists digital I/O terminal parameters with their attributes and default values.
Lists analogue I/O terminal parameters with their attributes and default values.
Lists fault protection parameters with their attributes and default values.
General| Brand | hpmont |
|---|---|
| Model | HD5L-4T7P5 |
| Category | Controller |
| Language | English |
