What causes Read / Write fault of control board EEPROM in hpmont Controller?
A read/write fault of the control board EEPROM in the hpmont Controller signifies a memory circuit fault of the control board EEPROM.
What to do if hpmont HD3L-4T5P5 Controller shows 'Acc overcurrent'?
If the hpmont Controller displays an 'Acc overcurrent' error, it could be due to an improper connection between the controller and motor, incorrect motor parameters, an undersized controller, or a too-short Acc/Dec time. Ensure the controller and motor are properly connected, verify the motor parameters, select a controller with a higher rating if necessary, and adjust the Acc/Dec time.
What causes hpmont HD3L-4T5P5 overload and how to fix it?
Controller overload in your hpmont device can occur if the Acc time is too short, the V/f curve or torque boost settings are incorrect, the mains supply voltage is too low, or the motor load is too high. Try adjusting the Acc time and V/f curve or torque boost settings. Also, check the mains supply voltage and consider using a controller with a proper power rating.
Why does hpmont HD3L-4T5P5 show 'Motor overload'?
The hpmont Controller may indicate a motor overload because of an improper V/f curve setting, low mains supply voltage, an incorrectly set motor overload protection factor, or a locked-rotor/overloaded motor. Adjust the V/f curve, check the power input, properly set the overload protection factor of the motor, and inspect the load and mechanical transmission devices.
What to do if hpmont HD3L-4T5P5 shows 'Acc over voltage'?
If the hpmont Controller is showing an 'Acc over voltage' error, the input voltage might be too high, the deceleration time might be too short, or the wiring is improper. Check the power input, set a proper value for Dec time, and verify the wiring.
What to do if hpmont HD3L-4T5P5 Controller shows 'Fault of external equipment'?
If the hpmont Controller indicates a 'Fault of external equipment', the fault terminal of external equipment operates. Check external equipment.
What causes parameter auto-tuning fault on hpmont Controller?
A parameter auto-tuning fault on the hpmont Controller indicates that the parameter auto-tuning has timed out. Check the motor connection and input correct nameplates parameters.
What causes soft start contactor failed in hpmont HD3L-4T5P5 Controller?
A soft start contactor failure in the hpmont Controller can result from a contactor fault or a control circuit fault. Replace the contactor.
What causes motor overheat in hpmont Controller?
Motor overheat with the hpmont Controller can be due to the motor overheating, incorrect connection of the motor overheat terminal, or incorrect motor parameter settings. Reduce the load, increase the Acc / Dec time, repair or replace the motor, detect whether the overheat detection input signal is correct and set the motor parameter according to the nameplate.
How to fix faulty setting of parameters on hpmont HD3L-4T5P5 Controller?
Faulty parameter settings on the hpmont Controller can result from a significant difference in power rating between the motor and controller, or from incorrect motor parameter settings. Select a controller with a suitable power rating and set the correct value of motor parameters.
Defines Danger, Warning, and Note for hazard and safety information.
Provides essential information about the HD3L controller's features and limitations.
Provides comprehensive technical specifications for the HD3L controller.
Safety precautions to be observed during the mechanical installation of HD3L.
Specifies the environmental and site conditions for HD3L installation.
Crucial safety warnings and precautions for electrical installation of HD3L.
Selection of peripheral accessories for HD3L, including wiring specs and terminal lugs.
Details on the main circuit connections for HD3L, including supply and motor terminals.
Information on HD3L's control board, I/O board, communication, and jumpers.
Guidelines for meeting EMC requirements, including correct installation and wiring.
Overview of HD3L controller functions, including operation modes and control modes.
Detailed instructions on using the HD3L keypad, display, and parameter settings.
Practical examples of keypad operations like parameter setting and password management.
Core operational parameters covering basic settings, protection, and motor control.
Configuration for various fault detection and protection mechanisms within the HD3L.
Step-by-step guide for initial setup and configuration of the HD3L for elevator systems.
Configuration for emergency operation using battery power during mains failure.
Guide to identifying and resolving common faults and error codes in the HD3L controller.
Procedures for daily, periodical, and component replacement maintenance of the HD3L.
General| Brand | hpmont |
|---|---|
| Model | HD3L-4T5P5 |
| Category | Controller |
| Language | English |
To Next Page
