To Next Page
B
Brian WestSep 7, 2025
What to do if hpmont HD5L-4T3P7 displays E0013 error?
- DDavid SullivanSep 7, 2025
If the hpmont Controller displays error E0013, which indicates soft start contactor failed, replace the contactor.
What to do if hpmont HD5L-4T3P7 displays E0013 error?
If the hpmont Controller displays error E0013, which indicates soft start contactor failed, replace the contactor.
What causes E0001 error on hpmont Controller and how to fix it?
The E0001 error on your hpmont Controller means Acc overcurrent. To resolve this, ensure that the HD5L and motor are properly connected, set the correct motor parameters, select a controller with a higher rating, and set proper Acc time and Dec time.
What to do if hpmont HD5L-4T3P7 Controller displays E0017 error?
If the hpmont Controller displays error E0017, which indicates a controller overload, you can adjust the Acc time, adjust the V/f curve or torque boost, check the mains supply voltage, or use a controller with proper power rating.
Why did the soft start fail on my hpmont Controller?
If the hpmont Controller indicates a 'Soft start failed' error, it could be due to a contactor fault or a fault in the control circuit. Replace the contactor.
What causes Braking unit fault in hpmont Controller?
If the hpmont Controller reports a Braking unit fault, it indicates a circuit fault within the braking unit. Please seek technical support.
Why is there excessive speed deviation in hpmont Controller?
If the hpmont Controller indicates excessive speed deviation, the possible causes are: a brake or contactor fault, PG pulse number fault, improper settings of F05.19 and F05.20, inadequate controller torque, or incorrect speed-loop PI parameter settings. To address this, consider the following: 1. Change the contactor 2. Set proper PG P/R 3. Correct the setting of F05.19 and F05.20 4. Select bigger capacity controller 5. Correctly set speed-loop PI parameter
What to do if hpmont HD5L-4T3P7 Controller displays E0024 error?
If the hpmont Controller displays error E0024, which indicates a fault of external equipment, check external equipment.
What to do if hpmont HD5L-4T3P7 displays E0028 error?
If the hpmont Controller displays error E0028, which indicates SCI communication timeout, check the connection.
What does Controlboard EEPROM faulty mean on hpmont HD5L-4T3P7 Controller?
If the hpmont Controller displays 'Controlboard EEPROM faulty', it means there is a memory circuit fault of control board EEPROM. Please contact the supplier for repairing.
Why hpmont Controller shows E0018 error?
The E0018 error on the hpmont Controller indicates excessive speed deviation. To fix it, change the contactor, set proper PG P/R, correct the setting of F05.19 - F05.20, select bigger capacity, and correctly set speed-loop PI parameter.
Details restrictions on output side components, voltage, input phases, and derating.
Lists electrical, performance, and protection specifications of the controller.
Provides a table of model ratings for single-phase and three-phase power supply.
Lists essential safety precautions that must be followed during installation.
Specifies environmental and spatial requirements for the installation location.
Outlines critical safety rules and precautions for electrical wiring.
Recommends peripheral devices for the main circuit based on model specifications.
Details the main circuit terminals and provides general wiring guidelines.
Discusses control circuit safety, cable management, and interference suppression.
Introduces different types of encoder cards and their respective functions.
Explains how to ensure Electromagnetic Compatibility (EMC) during installation.
Explains the step-by-step process for motor parameter auto-tuning.
Describes the battery-driven run mode for emergency situations during power outages.
Lists common fault codes, their possible reasons, and recommended countermeasures.
Lists fault protect parameters and their attributes.
General| Brand | hpmont |
|---|---|
| Model | HD5L-4T3P7 |
| Category | Controller |
| Language | English |
