What to do if hpmont HD5L-4T7P5 displays E0023 error?
If the hpmont Controller displays error E0023, which indicates a faulty setting of parameters, select a controller with a suitable power rating and set correct value of motor parameters.
What to do if hpmont Controller displays E0025 error?
If the hpmont Controller displays error E0025, which indicates too small running current, correct the setting of F16.14, F16.15, check the connection between HD5L and motor, detect HD5L whether output and detect whether the output contactor work is normal.
Why hpmont HD5L-4T7P5 shows E0018 error?
The E0018 error on the hpmont Controller indicates excessive speed deviation. To fix it, change the contactor, set proper PG P/R, correct the setting of F05.19 - F05.20, select bigger capacity, and correctly set speed-loop PI parameter.
How to troubleshoot DC bus undervoltage on hpmont HD5L-4T7P5 Controller?
If you are experiencing DC bus undervoltage with your hpmont Controller, it could be due to normal power on/off cycling, low input voltage, or improper wiring. Check the input power voltage and ensure the controller is wired properly. Note that undervoltage can occur at the beginning of power on and at the end of power off, which is normal.
Why did the soft start fail on my hpmont HD5L-4T7P5?
If the hpmont Controller indicates a 'Soft start failed' error, it could be due to a contactor fault or a fault in the control circuit. Replace the contactor.
What does Controlboard EEPROM faulty mean on hpmont HD5L-4T7P5 Controller?
If the hpmont Controller displays 'Controlboard EEPROM faulty', it means there is a memory circuit fault of control board EEPROM. Please contact the supplier for repairing.
What to do if hpmont Controller shows E0004 error?
If the hpmont Controller displays error E0004, which indicates Acc over voltage, you should check the power input, set a proper value for Dec time, and check wiring to ensure HD5L is wired properly.
What does Lu error mean on hpmont Controller?
The Lu error on the hpmont Controller indicates DC bus undervoltage. This can be normal during power on and power off. Check the input power voltage and ensure the HD5L wiring is correct.
What to do if hpmont HD5L-4T7P5 Controller displays E0019 error?
If the hpmont Controller displays error E0019, which indicates a motor overload, you can adjust the V/f curve, check the power input, properly set the overload protection factor of the motor, and check the load and mechanical transmission devices.
What to do if hpmont Controller displays E0017 error?
If the hpmont Controller displays error E0017, which indicates a controller overload, you can adjust the Acc time, adjust the V/f curve or torque boost, check the mains supply voltage, or use a controller with proper power rating.
General| Brand | hpmont |
|---|---|
| Model | HD5L-4T7P5 |
| Category | Controller |
| Language | English |
Details restrictions on output side connections, voltage, and input phase usage.
Lists detailed electrical, performance, characteristic, and protection specifications.
Provides a table of models, power ratings, input/output currents, and motor power.
Outlines essential safety precautions before and during controller installation.
Specifies environmental and spatial requirements for controller installation.
Lists critical safety precautions and guidelines for electrical wiring.
Covers terminal descriptions and wiring practices for the main power circuit.
Explains wiring precautions and general connections for the control circuit.
Provides guidelines for installation to meet EMC standards and reduce interference.
Defines the four modes for receiving run commands and setting speed.
Explains the five available running modes for the controller.
Provides step-by-step examples for setting parameters and managing user passwords.
Guides the user through the initial power-on and controller initialization process.
Outlines basic steps for system analysis, wiring, and parameter setup.
Provides a table listing fault codes, possible causes, and countermeasures.
Lists basic parameters with their attributes, default values, and ranges.
Lists parameters for parameter protection with their attributes and default values.
Lists start/stop parameters with their attributes and default values.
Lists acceleration/deceleration parameters with their attributes and default values.
Lists speed parameters with their attributes and default values.
Lists asynchronous motor parameters with their attributes and default values.
Lists speed-loop parameters for vector control with attributes and default values.
Lists synchronous motor parameters with their attributes and default values.
Lists PG (encoder) parameters with their attributes and default values.
Lists digital I/O terminal parameters with their attributes and default values.
Lists analogue I/O terminal parameters with their attributes and default values.
Lists fault protection parameters with their attributes and default values.
To Next Page
