What does Lu error mean on hpmont Controller?
The Lu error on the hpmont Controller indicates DC bus undervoltage. This can be normal during power on and power off. Check the input power voltage and ensure the HD5L wiring is correct.
What to do if hpmont Controller shows E0004 error?
If the hpmont Controller displays error E0004, which indicates Acc over voltage, you should check the power input, set a proper value for Dec time, and check wiring to ensure HD5L is wired properly.
What to do if hpmont HD5L-4T7P5 displays E0020 error?
If the hpmont Controller displays error E0020, indicating motor overheat, reduce the load, increase the Acc / Dec time, repair or replace the motor, detect whether the overheat detection input signal is correct, and set the motor parameter according to nameplate.
What to do if hpmont Controller displays E0032 error?
If the hpmont Controller displays error E0032, indicating motor over speed, set proper PG pulse number, select bigger capacity controller, and correctly set speed-loop PI parameter.
What to do if hpmont HD5L-4T7P5 displays E0016 error?
If the hpmont Controller displays error E0016, which indicates output voltage phase loss, check the connection between HD5L and the motor and check the quality of the motor.
Why hpmont HD5L-4T7P5 shows E0018 error?
The E0018 error on the hpmont Controller indicates excessive speed deviation. To fix it, change the contactor, set proper PG P/R, correct the setting of F05.19 - F05.20, select bigger capacity, and correctly set speed-loop PI parameter.
What to do if hpmont Controller displays E0025 error?
If the hpmont Controller displays error E0025, which indicates too small running current, correct the setting of F16.14, F16.15, check the connection between HD5L and motor, detect HD5L whether output and detect whether the output contactor work is normal.
What to do if hpmont HD5L-4T7P5 displays E0023 error?
If the hpmont Controller displays error E0023, which indicates a faulty setting of parameters, select a controller with a suitable power rating and set correct value of motor parameters.
What to do if hpmont Controller displays E0008 error?
If the hpmont Controller displays error E0008, which indicates a power module fault, check the connection and connect the wire properly and check the connection and mechanism.
What to do if hpmont Controller shows E0009 error?
If the hpmont Controller displays error E0009, which indicates a heatsink overheat, consider using a controller with a higher power capacity, improving the ventilation around HD5L, or replacing the cooling fan.
General| Brand | hpmont |
|---|---|
| Model | HD5L-4T7P5 |
| Category | Controller |
| Language | English |
Details restrictions on output side connections, voltage, and input phase usage.
Lists detailed electrical, performance, characteristic, and protection specifications.
Provides a table of models, power ratings, input/output currents, and motor power.
Outlines essential safety precautions before and during controller installation.
Specifies environmental and spatial requirements for controller installation.
Lists critical safety precautions and guidelines for electrical wiring.
Covers terminal descriptions and wiring practices for the main power circuit.
Explains wiring precautions and general connections for the control circuit.
Provides guidelines for installation to meet EMC standards and reduce interference.
Defines the four modes for receiving run commands and setting speed.
Explains the five available running modes for the controller.
Provides step-by-step examples for setting parameters and managing user passwords.
Guides the user through the initial power-on and controller initialization process.
Outlines basic steps for system analysis, wiring, and parameter setup.
Provides a table listing fault codes, possible causes, and countermeasures.
Lists basic parameters with their attributes, default values, and ranges.
Lists parameters for parameter protection with their attributes and default values.
Lists start/stop parameters with their attributes and default values.
Lists acceleration/deceleration parameters with their attributes and default values.
Lists speed parameters with their attributes and default values.
Lists asynchronous motor parameters with their attributes and default values.
Lists speed-loop parameters for vector control with attributes and default values.
Lists synchronous motor parameters with their attributes and default values.
Lists PG (encoder) parameters with their attributes and default values.
Lists digital I/O terminal parameters with their attributes and default values.
Lists analogue I/O terminal parameters with their attributes and default values.
Lists fault protection parameters with their attributes and default values.
To Next Page
