Huawei UPS5000-E-300K-SMT - 3.3 Installing a Parallel System

300 pages

To Next Page

To Previous Page

UPS5000-E-(50 kVA-300 kVA)

User Manual (50 kVA Power Modules)

3 Installation

Issue 02 (2017-02-25)

Huawei Proprietary and Confidential

105

Figure 3-68 Removing copper bars

Figure 3-69 shows the power cables routed from the bottom of the cabinet.

Main Page

About this Document3
Table of Contents5
Safety Precautions10
General Safety10
Electrical Safety12
Operating Environment15
Battery Safety15
Mechanical Safety18
Laying out Cables19
Overview21
Model Description21
Working Principle22
Conceptual Diagram22
Working Modes23
Normal Mode23
Bypass Mode24
Battery Mode25
Maintenance Bypass Mode26
ECO Mode27
Product Introduction28
Structure28
Power Module33
Bypass Module34
Control Module36
Overview36
Ecm36
Dry Contact Card38
Optional) Backfeed Protection Card40
Optional) Dry Contact Extended Card40
Monitoring Interface Card40
Typical Configurations45
Single UPS46
N+X Parallel System46
Dual-Bus System46
Optional Components47
Installation50
Installation Preparations50
Site50
Weight and Dimensions50
Installation Environment54
Installation Clearances54
Tools54
Preparing Power Cables56
Unpacking and Checking61
Installing a Single UPS64
Installing the Cabinet64
Installing Batteries70
Installing Optional Components71
Installing Antiseismic Kits71
Installing an IP21 Component73
Connecting an Ambient T/H Sensor74
Connecting the BCB Box75
Connecting the BBB Box75
Installing a Battery Grounding Failure Detector75
Connecting the Ibat77
UPS Cable Connection Reference78
Routing Cables (UPS5000-E-200K-SM)80
Routing Cables from the Top80
Routing Cables from the Bottom87
Routing Cables (UPS5000-E-200K-FM)92
Routing Cables from the Top92
Routing Cables from the Bottom99
Routing Cables (UPS5000-E-300K-SM)109
Routing Cables (UPS5000-E-300K-SMT)116
Remote EPO122
Connecting Communications Cables123
Installing a Parallel System123
Installing the Upss123
Connecting Power Cables125
Connecting Signal Cables128
Installation Verification130
User Interface133
LCD Interface133
Lcd133
LCD Menu134
Menu Hierarchy134
Initial Startup135
Main Menu136
System Info Screen137
Module Data Screen138
Runn Info Screen138
Alarms Screen146
Settings Screen149
Maintenance Screen178
About Screen185
System Status Screen185
Common Functions Screen186
Webui187
Login187
Monitoring Page189
Active Alarms Page190
Real-Time Data Page191
Param. Settings Page191
Comm. Config. Page192
CIM Parameters192
Control Page193
Query Page193
Historical Alarms Page193
Logs Page194
Config. Page194
User Management194
Site Config. Page195
Rccmd197
Managing the UPS by Using the NMS Complying with RFC1628 Standard206
Maint. Page207
Protecting the Server by Using the RCCMD Software209
Introduction to the Software209
RCCMD Event Shutdown and Message Sending209
UPS Alive Check Function211
Operations214
Powering on and Starting the UPS214
Shutting down and Powering off the UPS225
Starting the UPS in Battery Mode227
Transferring to Bypass Mode228
Setting ECO Mode228
Testing Batteries231
Forced Equalized Charging Test231
Shallow Discharge Test232
Capacity Test233
Test Data Download235
Download over the LCD235
Download over the Webui236
Transferring to Maintenance Bypass Mode237
Transferring from Maintenance Bypass Mode to Normal Mode240
Performing EPO242
Clearing the EPO State243
Exporting Data246
Setting Hibernation Mode247
Lcd248
Webui249
Routine Maintenance251
UPS Maintenance251
Monthly Maintenance251
Quarterly Maintenance252
Annual Maintenance252
Battery Maintenance253
Precautions for Battery Maintenance254
Monthly Maintenance254
Quarterly Maintenance255
Annual Maintenance256
Troubleshooting257
Technical Specifications259
Physical Specifications259
Internal Switch Parameters259
Environmental Specifications260
Safety Regulations and EMC260
Mains Input Electrical Specifications261
Bypass Input Electrical Specifications261
Battery Specifications262
Output Electrical Specifications262
System Electrical Specifications263
A (Optional) TN-C System Application264
B Menu Hierarchy267
Menus on the LCD267
Menus on the Webui269

Huawei UPS5000-E-300K-SMT - 3.3 Installing a Parallel System

Table of Contents

Other manuals for Huawei UPS5000-E-300K-SMT

Related product manuals