IBM Storwize V7000 Gen2 User Manual

Table 5. Steps for different installation scenarios
New system (control
enclosure only)
New system (control
enclosure and one or
more expansion
enclosures)
Adding expansion
enclosures to an
existing system
Adding control
enclosures and
expansion enclosures
to an existing system
“Reviewing your
packing slip” on
page 5
“Reviewing your
packing slip” on
page 5
“Reviewing your
packing slip” on
page 5
“Reviewing your
packing slip” on
page 5
“Identifying the
hardware
components” on page
6
“Identifying the
hardware
components” on page
6
“Identifying the
hardware
components” on page
6
“Identifying the
hardware
components” on page
6
“Verifying
environmental
requirements” on
page 9
“Verifying
environmental
requirements” on
page 9
“Verifying
environmental
requirements” on
page 9
“Verifying
environmental
requirements” on
page 9
“Reviewing enclosure
location guidelines”
on page 9
“Reviewing enclosure
location guidelines”
on page 9
“Reviewing enclosure
location guidelines”
on page 9
“Reviewing enclosure
location guidelines”
on page 9
“Installing support
rails for the control
enclosure” on page
11
“Installing
support rails for
the control
enclosure” on
page 11
“Installing
support rails for
expansion
enclosures” on
page 15
“Installing support
rails for expansion
enclosures” on page
15
1
“Installing
support rails for
the control
enclosure” on
page 11
“Installing
support rails for
expansion
enclosures” on
page 15
2
“Installing the
enclosures” on page
19
“Installing the
enclosures” on page
19
“Installing the
enclosures” on page
19
1
“Installing the
enclosures” on page
19
2
“Connecting Ethernet
cables to node
canisters” on page 24
“Connecting SAS
cables to expansion
enclosures” on page
21
“Connecting SAS
cables to expansion
enclosures” on page
21
1
“Connecting SAS
cables to expansion
enclosures” on page
21
1
“Connecting Fibre
Channel cables to
a 10 Gbps
iSCSI-FCoE 4-port
host interface
card” on page 25
“Connecting Ethernet
cables to node
canisters” on page 24
“Powering on the
system” on page 27
1
“Connecting Ethernet
cables to node
canisters” on page
24
2
“Powering on the
system” on page 27
“Connecting Ethernet
cables to node
canisters” on page 24
“Adding an
expansion enclosure
to an existing
system” on page 33
Chapter 3,
“Configuring the
system,” on page 29
“Powering on the
system” on page 27
“Powering on the
system” on page 27
Chapter 3,
“Configuring the
system,” on page 29
“Adding a control
enclosure to an
existing system” on
page 33
2 Storwize V7000 Gen2: Quick Installation Guide

IBM Storwize V7000 Gen2 Specifications

General

Model	Storwize V7000 Gen2
Drive Interface	SAS
Maximum Drives	504
RAID Levels	0, 1, 5, 6, 10
Cache	Yes
Form Factor	2U
Cache Memory	64 GB per control enclosure
Operating System	IBM Spectrum Virtualize
Humidity	8% to 80% non-condensing
Drive Types Supported	SSD
Power Supply	Dual, hot-swappable
Host Interface	Fibre Channel, iSCSI, FCoE
Maximum Host Ports	16
Input Voltage	100-240 V AC
Operating Temperature	10°C to 35°C
Non-operating Temperature	-10°C to 50°C