Why is my Immergas Boiler showing a fan anomaly?
If your Immergas Boiler displays a fan anomaly, it means the fan likely has a mechanical or electrical fault. To attempt to resolve this, press the Reset button.
What does it mean when my Immergas Boiler shows a flue safety thermostat block?
If your Immergas Boiler blocks due to excessive flue gas overheating during normal operation, press the Reset button to resolve the issue.
What does 'High temperature block on return probe' mean for my Immergas VICTRIX EXA 24 X 1 ErP?
If your Immergas Boiler shows a high temperature block on the return probe, it means the heat exchanger return circuit has reached a temperature that is too high. Make sure that water circulates properly in the boiler and that the three-way valve works properly. Press the Reset button to eliminate it.
What to do if my Immergas VICTRIX EXA 24 X 1 ErP is blocked due to insufficient circulation?
If your Immergas Boiler is blocked due to insufficient circulation, which can occur due to overheating from low system circulation or a blocked pump, press the Reset button. Also, check that no shut-off devices are closed on the heating circuit and ensure the system is free of air. If the pump is blocked, free the pump.
What to do if my Immergas Boiler experiences a loss of remote control communication?
If your Immergas Boiler loses communication with the remote control, power cycle the boiler. If the Remote Control is still not detected on re-starting, the boiler will switch to local operating mode, i.e. using the controls on the control panel.
What to do if the Immergas Boiler system pressure is insufficient?
If the Immergas Boiler displays insufficient system pressure, it means the water pressure inside the central heating circuit isn't sufficient for proper operation. Check the boiler pressure gauge to ensure the system pressure is between 1 and 1.2 bar. If it's not, restore the correct pressure.
What to do if my Immergas VICTRIX EXA 24 X 1 ErP Boiler shows 'Contacts resistance block'?
If your Immergas Boiler displays a 'Contacts resistance block', the P.C.B. has detected an anomaly on the gas valve supply. Check the connection. The anomaly is detected and displayed only when there is a request. To fix this, press the Reset button.
What does 'Flue safety thermostat block' mean on my Immergas Boiler, and how to fix it?
If your Immergas boiler displays a 'Flue safety thermostat block', it signifies that a fault has caused excessive fuel gas overheating during normal operation. To resolve this, press the Reset button.
What to do if my Immergas Boiler shows a safety thermostat block (over-temperature)?
If your Immergas Boiler goes into overheating block, it means a fault caused excessive overheating internally during normal operation. To fix this, press the Reset button.
What does it mean if my Immergas VICTRIX EXA 24 X 1 ErP experiences loss of flame signal?
If your Immergas Boiler experiences a loss of flame signal, it means the burner flame went out unexpectedly after the boiler ignited correctly. A new ignition attempt will be made, and if normal conditions are restored, the boiler will restart without needing a reset.
Provides essential guidelines and precautions for proper boiler installation.
Details the physical dimensions and connection points of the boiler unit.
Specifies the required clearance space around the boiler for safe installation.
Explains the boiler's built-in antifreeze function and protection measures.
Describes the optional kit for connecting the boiler's hydraulic and gas systems.
Outlines the procedures and precautions for connecting the boiler to the gas supply.
Details the correct methods for connecting the boiler to the heating and water systems.
Explains the electrical safety requirements and connection procedures for the boiler.
Describes the optional devices for remote boiler control and temperature management.
Explains the function and connection of the optional external temperature sensor.
Covers the specifications and installation of Immergas flue and air intake systems.
Provides guidelines for installing the boiler in outdoor partially protected locations.
Details the installation process for horizontal concentric flue kits.
Details the installation process for vertical concentric flue kits.
Explains the installation of the separator kit for divided flue systems.
Describes the installation of the C9 kit for specific shaft configurations.
Covers the process and regulations for ducting flue gases through various openings.
Specifies installation requirements for Type B indoor configurations.
Details options for connecting flue exhaust to existing flues or chimneys.
Covers compliance requirements for flue components and terminals.
Explains the procedure for filling the central heating system with water.
Describes how to fill the condensate drain trap to prevent flue gas leakage.
Outlines the steps for safely starting up the gas system.
Details the procedure for commissioning and igniting the boiler.
Explains the settings and operation of the boiler's circulation pump.
Covers advanced functions and diagnostics for the circulation pump.
Lists optional kits that can be purchased to enhance boiler functionality.
Identifies and labels the key components of the boiler unit.
Lists crucial safety precautions and warnings for boiler users.
Outlines the recommended procedures for cleaning and routine maintenance.
Explains the functions and indicators of the boiler's control panel.
Guides users on operating the boiler for heating and hot water production.
Helps identify and resolve common boiler faults and error codes.
Describes how to access and interpret the boiler's operating parameters and status.
Explains the correct procedure for turning off the boiler.
Guides on how to check and maintain the correct pressure in the heating system.
Details the process for safely draining the heating system.
Explains how to drain the domestic hot water circuit.
Provides information on antifreeze functions and system protection.
Recommends methods for cleaning the boiler's external casing.
Outlines procedures for safely decommissioning the boiler.
Specifies requirements for re-commissioning gas systems after long periods of disuse.
Lists essential safety precautions for maintenance personnel.
Details the essential annual checks and maintenance tasks for the boiler.
Presents a visual representation of the boiler's hydraulic circuits and components.
Illustrates the boiler's electrical connections and component layout.
Lists common issues, their causes, and potential solutions.
Explains the process and requirements for converting the boiler to different gas types.
Specifies checks required after converting the boiler to a different gas type.
Details the procedure for calibrating the fan speed for optimal performance.
Explains how to adjust the CO₂ levels for efficient combustion.
Guides on how to program the boiler's printed circuit board for custom settings.
Describes how to integrate solar panels for DHW heating.
Explains the function that forces the boiler to variable output for testing.
Details the function that prevents the pump from becoming blocked.
Explains the function that prevents the three-way valve from becoming blocked.
Describes the function that protects radiators from freezing.
Explains the periodic self-check function of the boiler's PCB.
Details the function for automatic air release from the system.
Provides step-by-step instructions for removing the boiler casing for maintenance.
Details the boiler's adjustable heat output ranges and related pressures.
Lists key combustion parameters for different gas types and operating conditions.
Presents a comprehensive table of the boiler's technical specifications and performance metrics.
Explains the meaning of the various fields and codes found on the boiler's data nameplate.
Provides technical data specifically for combination boiler functions.
Presents the official product fiche and energy label information.
Guides on how to fill in package fiche details using technical data.
To Next Page
General