What to do if my Immergas Boiler shows no ignition block?
If your Immergas Boiler doesn't switch on when you request central heating or hot water, especially after first use or a long break, it might be blocked. To fix this, press the Reset button.
Why does my Immergas Boiler show a safety thermostat block (over-temperature)?
If your Immergas boiler overheats due to a fault during normal operation, it will enter an overheating block. To resolve this, press the Reset button.
What should I do if my Immergas VICTRIX EXA 24 X 1 ErP displays insufficient system pressure?
If your Immergas Boiler indicates insufficient system pressure, check the pressure gauge on the boiler. Ensure the pressure is between 1 and 1.2 bar. If it's lower, restore the pressure to the correct level.
What to do if my Immergas VICTRIX EXA 24 X 1 ErP Boiler is blocked due to fuel gas temperature gradient intervention?
If your Immergas Boiler shuts down because of a rapid increase in fuel gas temperature, possibly due to a blocked circulating pump or lack of water in the heat exchanger, it's experiencing a fuel gas temperature gradient trip. To resolve this, press the Reset button.
What does it mean when my Immergas Boiler shows a flue safety thermostat block?
If your Immergas Boiler blocks due to excessive flue gas overheating during normal operation, press the Reset button to resolve the issue.
Why is my Immergas Boiler showing a fan anomaly?
If your Immergas Boiler displays a fan anomaly, it means the fan likely has a mechanical or electrical fault. To attempt to resolve this, press the Reset button.
What to do if my Immergas VICTRIX EXA 24 X 1 ErP displays 'Block due to loss of continuous flame signal'?
If your Immergas Boiler shows 'Block due to loss of continuous flame signal' because the flame signal was lost repeatedly, press the Reset button. The boiler will then run a post-ventilation cycle before restarting.
What does it mean if my Immergas Boiler displays 'Parasite flame block'?
If your Immergas Boiler displays a 'Parasite flame block', it indicates a leak in the detection circuit or an anomaly in the flame control unit. To address this, press the Reset button.
What to do if my Immergas Boiler is showing 'contacts resistance block'?
If your Immergas Boiler displays a 'contacts resistance block', the P.C.B. has detected an anomaly on the gas valve supply. Check the connection. To attempt to resolve this, press the Reset button.
What to do if my Immergas Boiler has a configuration error?
If your Immergas Boiler detects an anomaly or incongruity in the electrical wiring, it won't start. Check that the boiler is configured correctly. If normal conditions are restored, the boiler will restart without needing a reset.
Provides essential guidelines and precautions for proper boiler installation.
Details the physical dimensions and connection points of the boiler unit.
Specifies the required clearance space around the boiler for safe installation.
Explains the boiler's built-in antifreeze function and protection measures.
Describes the optional kit for connecting the boiler's hydraulic and gas systems.
Outlines the procedures and precautions for connecting the boiler to the gas supply.
Details the correct methods for connecting the boiler to the heating and water systems.
Explains the electrical safety requirements and connection procedures for the boiler.
Describes the optional devices for remote boiler control and temperature management.
Explains the function and connection of the optional external temperature sensor.
Covers the specifications and installation of Immergas flue and air intake systems.
Provides guidelines for installing the boiler in outdoor partially protected locations.
Details the installation process for horizontal concentric flue kits.
Details the installation process for vertical concentric flue kits.
Explains the installation of the separator kit for divided flue systems.
Describes the installation of the C9 kit for specific shaft configurations.
Covers the process and regulations for ducting flue gases through various openings.
Specifies installation requirements for Type B indoor configurations.
Details options for connecting flue exhaust to existing flues or chimneys.
Covers compliance requirements for flue components and terminals.
Explains the procedure for filling the central heating system with water.
Describes how to fill the condensate drain trap to prevent flue gas leakage.
Outlines the steps for safely starting up the gas system.
Details the procedure for commissioning and igniting the boiler.
Explains the settings and operation of the boiler's circulation pump.
Covers advanced functions and diagnostics for the circulation pump.
Lists optional kits that can be purchased to enhance boiler functionality.
Identifies and labels the key components of the boiler unit.
Lists crucial safety precautions and warnings for boiler users.
Outlines the recommended procedures for cleaning and routine maintenance.
Explains the functions and indicators of the boiler's control panel.
Guides users on operating the boiler for heating and hot water production.
Helps identify and resolve common boiler faults and error codes.
Describes how to access and interpret the boiler's operating parameters and status.
Explains the correct procedure for turning off the boiler.
Guides on how to check and maintain the correct pressure in the heating system.
Details the process for safely draining the heating system.
Explains how to drain the domestic hot water circuit.
Provides information on antifreeze functions and system protection.
Recommends methods for cleaning the boiler's external casing.
Outlines procedures for safely decommissioning the boiler.
Specifies requirements for re-commissioning gas systems after long periods of disuse.
Lists essential safety precautions for maintenance personnel.
Details the essential annual checks and maintenance tasks for the boiler.
Presents a visual representation of the boiler's hydraulic circuits and components.
Illustrates the boiler's electrical connections and component layout.
Lists common issues, their causes, and potential solutions.
Explains the process and requirements for converting the boiler to different gas types.
Specifies checks required after converting the boiler to a different gas type.
Details the procedure for calibrating the fan speed for optimal performance.
Explains how to adjust the CO₂ levels for efficient combustion.
Guides on how to program the boiler's printed circuit board for custom settings.
Describes how to integrate solar panels for DHW heating.
Explains the function that forces the boiler to variable output for testing.
Details the function that prevents the pump from becoming blocked.
Explains the function that prevents the three-way valve from becoming blocked.
Describes the function that protects radiators from freezing.
Explains the periodic self-check function of the boiler's PCB.
Details the function for automatic air release from the system.
Provides step-by-step instructions for removing the boiler casing for maintenance.
Details the boiler's adjustable heat output ranges and related pressures.
Lists key combustion parameters for different gas types and operating conditions.
Presents a comprehensive table of the boiler's technical specifications and performance metrics.
Explains the meaning of the various fields and codes found on the boiler's data nameplate.
Provides technical data specifically for combination boiler functions.
Presents the official product fiche and energy label information.
Guides on how to fill in package fiche details using technical data.
To Next Page
General