Immergas Victrix Tera 38 1 - External Temperature Probe (Optional)

45
31
58
10
11
INSTALLERUSER
MAINTENANCE TECHNICIAN
14
EXTERNAL PROBE
Correction law of the ow temperature depending on the external temperature and
user adjustment of the central heating temperature.
• On/O Immergas digital chrono-thermostat.
e chrono-thermostat allows:
- set two room temperature values: one for day (comfort tem-
perature) and one for night (reduced temperature);
- set a weekly programme with four daily switch on and switch
o times;
- select the required operating mode from the various possible
alternatives:
• manual mode (with adjustable temperature);
• automatic mode (with set programme);
• forced automatic mode (momentarily changing the temperature
of the automatic programme).
e chrono-thermostat is powered by two 1.5V LR 6 type alkaline
batteries;
• Comando Amico Remoto Remote Control Device
V2
(CAR
V2
)
with climate chrono-thermostat function.
In addition to the functions described in the previous point,
the CAR
V2
panel enables the user to control all the important
information regarding operation of the appliance and the heating
system with the opportunity to easily intervene on the previously
set parameters, without having to go to where the appliance is
installed. e panel is provided with self-diagnosis to display
any boiler functioning anomalies. e climate chrono-thermo-
stat incorporated into the remote panel enables the system ow
temperature to be adjusted to the actual needs of the room being
heated, in order to obtain the desired room temperature with
extreme precision and therefore with evident saving in running
costs. e CAR
V2
is fed directly by the boiler by means of the
same 2 wires used for the transmission of data between the boiler
and device.
Comando Amico Remoto Remote Control
V2
or On/Off
chrono-thermostat electrical connections (Optional). e op-
erations described below must be performed aer having removed
the voltage from the appliance. Any thermostat or On/O environ-
ment chrono-thermostat must be connected to clamps 44/40 and
41 eliminating jumper X40 (Fig. 39). Make sure that the On/O
thermostat contact is “dry”, i.e. independent of the mains voltage,
otherwise the P.C.B. would be damaged. Any Comando Amico
Remoto remote control
V2
must be connected to terminals 44/40
and 41, eliminating jumper X40 on the P.C.B. ( Fig. 39). e boiler
can only be connected to one remote control.
If the Comando Amico Remoto remote control
V2
or
any other On/O chrono-thermostat is used arrange
two separate lines in compliance with current regu-
lations regarding electrical systems. No boiler pipes
must ever be used to earth the electric system or telephone
lines. Ensure elimination of this risk before making the boiler
electrical connections.
1.11 EXTERNAL TEMPERATURE PROBE OPTIONAL.
e boiler is designed for the application of the external tempera-
ture probe (Fig. 10), which is available as an optional kit. Refer to
the relative instruction sheet for positioning of the external probe.
The probe can be connected directly to the boiler electrical
system and allows the max. system ow temperature to be au-
tomatically decreased when the external temperature increases,
in order to adjust the heat supplied to the system according to
the change in external temperature. e external probe always
operates when connected, regardless of the presence or type of
room chrono-thermostat used and can work in combination with
Immergas chrono-thermostats. e correlation between system
ow temperature and external temperature is determined by the
position of the central heating selector switch on the boiler control
panel (or on the CAR
V2
control panel if connected to the boiler)
according to the curves shown in the diagram (Fig. 11). e elec-
tric connection of the external probe must be made on clamps 38
and 39 on the terminal board in the boiler control panel (Fig. 39).
Position of the central heating
temperature user adjustment