What to do if IN-COMMAND JRVCS2 Display Commander (DC) will not turn ON?
If the Display Commander doesn't turn on, try these steps: First, cycle the power using the ON/OFF button. If that doesn't work, check the main fuse in the Distribution Panel. Also, check for 12V+ on the wire to the DC (RED wire) and verify the Ground wire connection to the DC.
What to do if IN-COMMAND Control Systems Body Control Module (BCM) has no power?
If there is no power to the Body Control Module (BCM), try the following: Cycle the power using the ON/OFF button. Check if the red power LED is off. Verify the fuse in the Distribution Panel. Check for 12V+ on the wire at pin 80 and check the ground wire at pin 77.
Why is the IN-COMMAND JRVCS2 Control Systems DC screen flashing on and off after installation?
If the DC screen is flashing on and off after installation, try this: Disconnect the 12V+ and Ground wires from the back of the DC. Shut off all power to both the BCM and DC. Reconnect the 12V+ and Ground wires to the back of the DC, then restore power to the BCM and DC.
How to fix IN-COMMAND JRVCS2 Control Systems relay that is not activating?
General| Product Type | RV Control System |
|---|---|
| Power Supply | 12V DC |
| Connectivity | Bluetooth |
| App Compatibility | iOS, Android |
| Control Interface | Mobile App |
Safety warning about operating while driving.
Warning that the product is for adult use only, not for children.
Safety instruction to maintain a clear line of sight during operation.
Prohibition of operating under the influence of alcohol or drugs.
Caution to avoid exposing the equipment to moisture.
Recommendation to use only recommended accessories for safety.
Expresses gratitude to the user for choosing the product.
Lists the key features of the iN-Command system.
Provides essential safety and operational precautions.
Lists the items included in the product package.
Lists necessary tools and supplies for installation.
Steps to disconnect the battery before installation.
Guidance on choosing an appropriate mounting location.
Instructions for mounting the Display Commander unit.
Details the wiring connections for the Body Control Module.
Options to configure generator, fuel station, and tank monitoring.
Options to configure slides, awnings, and light groups.
Options for configuring triggers, alarms, and hitch.
Explains the Safety Lockout feature for transit.
Instructions on how to turn off the Safety Lockout.
Describes the function of override switches on the Body Control Module.
Notes that hydraulic overrides are on the pump, not BCM.
Technical specifications for DC, BCM, and the overall JRVCS2 system.
Information regarding FCC compliance and potential interference.
Instructions for entering and confirming a new system passcode.
Describes actions available from the Menu screen.
Guide on how to edit the text displayed for system functions.
Instructions on how to rearrange items in the scroll list.
Details on configuring tank levels and light groups.
Configuration options for slides and awnings.
Configuration options for jacks and triggers.
Instructions on how to enable or disable the system passcode.
Procedure to set the idle time for passcode activation.
Steps to modify the current system passcode.
Process to remove the system passcode.
Information on pairing mobile devices with the iN-Command system.
Details on the number of devices that can be actively paired.
Step-by-step guide for pairing a mobile device to the Display Commander.
Detailed steps for pairing an Android device with the DC.
Detailed steps for pairing an Apple device with the DC.
Instructions on how to reset the floor plan to default or previous settings.
How to view information about currently active Bluetooth devices.
Steps to prepare for software updates, including USB drive insertion.
Steps to perform software updates for DC, BCM, and APP.
Steps to update the DC's operating system.
Steps to update the Body Control Module firmware.
Steps to update the DC application software.
Instructions on selecting and loading a new floor plan file.
Explains restoring to manufacturer or factory default floor plan settings.
Procedure to enter the engineer passcode for calibration.
Steps to access the Admin menu for system calibration.
Entering the admin passcode for calibration tasks.
Setting resistor reference values for each tank.
How to activate the Auto Generator Start feature.
Explains the battery voltage conditions for starting the generator.
Details on generator run time and fault reporting.
Solutions for DC power and front panel operation problems.
Solutions for issues related to the Body Control Module power.
Troubleshooting steps for a flashing DC screen after installation.
Solutions for awnings and slide rooms not moving.
Troubleshooting for relay activation and DC showing 0V.
To Next Page
