Infineon TLE92464ED - User Manual

User Manual Please read the Important Notice and Warnings at the end of this document V1.1
www.infineon.com 2021-05-03
Next Generation Solenoid Driver
Evaluation Kit User Manual
About this document
This document explains how the Evaluation Kit for the NextGen Solenoid Driver ICs TLE92464ED and
TLE92466ED are taking into operation. The required hardware and software components for the evaluation of
the Next Gen Solenoid Driver IC TLE92464ED/TLE92466ED are documentated. See the TLE92464ED/TLE92466ED
datasheet for a detailed description of the device.
Note: All references of the TLE92464ED Evaluation board within this document are also valid for
TLE92466ED Evaluation board.
Intended audience
This document is intended for anyone who uses the Next Gen Solenoid Driver Evaluation Kit.
Table of contents
About this document ....................................................................................................................... 1
Table of contents ............................................................................................................................ 1
1 Hardware .............................................................................................................................. 2
1.1 Eval PCB ................................................................................................................................................... 2
1.1.1 Connector Interface for Arduino ........................................................................................................ 4
1.1.2 Jumper Options ................................................................................................................................. 7
1.1.3 LEDs .................................................................................................................................................... 7
1.2 Connection PCB ....................................................................................................................................... 7
1.2.1 Connector Interface for TriBoard TC277 ........................................................................................... 8
1.2.2 Jumper Options ................................................................................................................................. 9
1.3 Version S setup ........................................................................................................................................ 9
1.4 Version L setup ...................................................................................................................................... 11
1.5 Schematics ............................................................................................................................................ 11
2 Software .............................................................................................................................. 22
2.1 Flashing/Updating Aurix TC277 Software ............................................................................................ 22
2.2 Flashing/Updating XMC Software ......................................................................................................... 22
2.3 XMC for Arduino IDE .............................................................................................................................. 23
2.4 Graphical User Interface (GUI) .............................................................................................................. 24
2.4.1 Main Window .................................................................................................................................... 24
2.4.2 Evaluation Board Tabs ..................................................................................................................... 25
2.5 Information on the GUI communication interface............................................................................... 27
2.5.1 List of Commands ............................................................................................................................ 27
Revision history............................................................................................................................. 30

Infineon TLE92464ED Specifications

General

Brand	Infineon
Model	TLE92464ED
Category	Motherboard
Language	English

Summary

About this document

Intended audience

Specifies the target users for this evaluation kit user manual.

Hardware

Eval PCB

Details the Evaluation PCB, its components, and Arduino form-factor compatibility.

Connector Interface for Arduino

Describes the pinout and signals for the Arduino-compatible connector X1 on the Eval PCB.

Eval PCB Jumper Options

Explains configuration options via jumpers on the Evaluation PCB for various settings.

LEDs

Describes the function of LEDs on the Evaluation PCB indicating IC status.

Connection PCB

Introduces the Connection PCB used in version L for advanced measurements and parallel evaluation.

Connector Interface for TriBoard TC277

Details the interface between the Connection PCB and the TriBoard TC277 microcontroller.

Connection PCB Jumper Options

Explains jumper configurations on the Connection PCB for various settings.

Version S setup

Guides the setup for Evaluation Kit Version S using an XMC1100 microcontroller.

Version L setup

Guides the setup for Evaluation Kit Version L using a TC277 microcontroller TriBoard.

Schematics

Contains the schematic diagrams for the Evaluation PCBs and the Connection PCB.

Software

Flashing;Updating Aurix TC277 Software

Provides steps for flashing firmware onto the Aurix TC277 TriBoard for GUI communication.

Flashing;Updating XMC Software

Explains how to flash firmware onto XMC microcontrollers for GUI control.

XMC for Arduino IDE

Describes how to write and update software projects for XMC microcontrollers using Arduino IDE.

Graphical User Interface (GUI)

Details the setup and use of the Graphical User Interface for controlling the evaluation board.

Information on the GUI communication interface

Explains how the GUI communicates with the TriBoard via UART commands.

Revision history