Playback
En-52
When you connect an u-capable Integra/Onkyo
component, you must configure the input display so
that u can work properly.
This setting can be done only from the front panel.
You can temporarily mute the output of the AV
receiver.
You can set which speakers you want to use by
priority.
Note
• This setting is not available in either of the following cases:
– The “Speakers Type(Front)” setting is set to “Bi-Amp” or
“Digital Crossover” (➔ page 63).
– The “Powered Zone 2” setting is set to “Yes”
(➔ page 63).
• Playback conditions may be limited depending on the
settings in “Speaker Settings” (➔ page 63) and
“Speaker Configuration” (➔ page 63).
• When a listening mode which doesn’t support front high,
front wide or surround back speakers is used, this setting
cannot be selected.
The Whole House Mode is useful when you want to
add extra background music to your home party; this
allows you to enjoy the same stereo music as the
main room in separate rooms (Zone 2/3).
The Whole House Mode selects the same input
source for Multi Zone as the main room’s.
See also:
• “2. Speaker Setup” (➔ page 63)
• “Multi Zone” (➔ page 82)
Changing the Input Display
1
Press TV/CD or Game1.
“TV/CD” or “GAME1” appears on the AV
receiver’s display.
2
Press and hold down the same button (about
3 seconds) to change the input display.
Repeat this step to select the desired input
display.
Note
“
•“DOCK” can be selected for the “TV/CD” or “GAME1”
input selector, but not at the same time.
• Enter the appropriate remote control code before using
the remote controller for the first time (➔ page 87).
Muting the AV Receiver
1
Press Receiver followed by Muting.
The output is muted and the MUTING indicator
flashes on the AV receiver’s display.
Tip
• To unmute, press Muting again or adjust the volume.
• Muting is automatically cancelled when the AV
receiver is set to standby.
TV/CD → DOCK
→
→
TAPE
■ TV/CD:
GAME1 ↔ DOCK■ Game1:
Selecting Speaker Layout
1
Press Receiver followed by SP (speaker
layout) repeatedly to select:
■ 9.1 ch playback
` Speaker Layout:SB/FH:
The sounds from surround back and front
high speakers are output by priority.
` Speaker Layout:SB/FW:
The sounds from surround back and front
wide speakers are output by priority.
` Speaker Layout:FH/FW:
The sounds from front high and front wide
speakers are output by priority.
Important:
• The following layouts are only available when the
“11ch Playback” is set to “No” (➔ page 63) and all
corresponding speakers are enabled.
Using the Whole House Mode
1
Press Whole House Mode on the front panel.
To cancel the Whole House Mode, press Off,
change the input source for the main room or
select a listening mode (➔ page 43).
Note
• The Whole House Mode only supports analog audio
and audio from NET or USB input selector.
• To adjust the volume of Multi Zone, switch the AV
receiver to Multi Zone control. See “Adjusting the
Volume for Zones” (➔ page 83) for the volume
adjustment of Multi Zone.
• The Whole House Mode is not available in either of the
following cases:
– The “Audio TV Out (HDMI)” setting is set to “On”
(➔ page 78) or “Audio TV Out (HDBaseT(TM))”
setting is set to “On” (➔ page 78) and you’re
listening through your TV speakers.
–“HDMI CEC (RIHD)” is set to “On” (➔ page 77) and
you’re listening through your TV speakers.
– a pair of headphones is connected.
– The “Speakers Type(Front)” setting is set to
“Digital Crossover” (➔ page 63).
To Next Page
Loading...
