Integra DTR-60.5 - Page 64

Advanced Operations
En-64
Operating procedure (➔ page 59)
■ Subwoofer
` Yes
` No
■ Front
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz,
80Hz(THX)
, 90Hz, 100Hz, 110Hz, 120Hz, 130Hz,
150Hz, 200Hz
Note
• If the “Subwoofer” setting is set to “No”, the “Front” setting
is fixed at “Full Band”.
■ Center
*1
, Surround
*1
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz,
80Hz(THX)
, 90Hz, 100Hz, 110Hz, 120Hz, 130Hz,
150Hz, 200Hz
` None
■ Front Wide
*1*2*4*6*7
, Front High
*1*2*5*6
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz,
80Hz(THX), 90Hz, 100Hz, 110Hz, 120Hz, 130Hz,
150Hz, 200Hz
` None
■ Surround Back
*2*3*8*9
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz,
80Hz(THX), 90Hz, 100Hz, 110Hz, 120Hz, 130Hz,
150Hz, 200Hz
` None
Note
*1
“Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*2
If the “Surround” setting is set to “None”, this setting
cannot be selected.
*3
If the “Surround” setting is set to anything other than
“Full Band”, “Full Band” cannot be selected here.
*4
When the “Powered Zone 2” setting is set to “Yes”, this
setting cannot be selected.
*5
When the “Powered Zone 3” setting is set to “Yes”, this
setting cannot be selected.
*6
This setting cannot be selected if the “Speakers Type
(Front)” setting is set to “Bi-Amp” or “Digital
Crossover”.
*7
If the “11ch Playback” setting is enabled, “None” cannot
be selected.
*8
When the “Powered Zone 3” setting is set to “Yes”
(➔ page 63) while Powered Zone 2 is enabled
(➔ page 83), this setting cannot be selected.
*9
When the “Speakers Type(Front)” setting is set to
“Bi-Amp” or “Digital Crossover” while Powered Zone 2
is enabled (➔ page 83), this setting cannot be selected.
■ Surround Back Ch
` 1ch:
Select if only one surround back speaker L is
connected.
` 2ch
:
Select if two (left and right) surround back
speakers are connected.
Note
• If the “Surround Back” setting is set to “None”, this setting
cannot be selected.
■ LPF of LFE
(Low-Pass Filter for the LFE Channel)
` 80Hz, 90Hz, 100Hz, 110Hz, 120Hz
` Off:
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff
frequency of the LFE channel’s low-pass filter
(LPF), which can be used to filter out unwanted
hum. The LPF only applies to sources that use the
LFE channel.
Note
• If you’re using THX-certified speakers, select “80Hz”.
■ Subwoofer Phase
` 0
º
` 180º:
Moves the subwoofer phase.
Note
• If the “Subwoofer” setting is set to “No”, this setting cannot
be selected.
■ Double Bass
` On
` Off(THX)
Turn this setting on to boost bass output by feeding
bass sounds from the front left, right, and center
channels to the subwoofer. Default setting: “
-----”
Note
• When the “Subwoofer” setting is set to “No” or the “Front”
setting to anything other than “Full Band”, this setting is
fixed to “-----”.
• This setting is set to “On” automatically when the
“Subwoofer” and “Front” settings are set for the first time
to “Yes” and “Full Band” respectively.
• If you’re using THX-certified speakers, select “Off(THX)”.
Speaker Distance
Here you can specify the distance from each speaker
to the listening position so that the sound from each
speaker arrives at the listener’s ears as the sound
designer intended.
This setting is NOT set automatically by
Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup function (➔ page 26).
This setting is set automatically by
Audyssey MultEQ XT32 Room Correction and
Speaker Setup function (➔ page 26).