Intel Agilex I Series User Manual

Electrostatic Discharge (ESD) Warning
A properly grounded ESD wrist strap must be worn during operation/installation of the
boards, connection of cables, or during installation or removal of daughter cards.
Failure to use wrist straps can damage components within the system.
Attention: Please return this product to Intel for proper disposition. If it is not returned, refer to
local environmental regulations for proper recycling. Do not dispose of this product in
unsorted municipal waste.
Lithium Ion Battery Warnings
Lithium Battery: Risk of explosion if the lithium battery is replaced by an incorrect
type. Risk of fire, explosion, or chemical burn if the battery is mistreated (punctured
or crushed). Do not attempt to disassemble. Do not incinerate. Observe proper
polarity when replacing battery. Do not dispose—the battery is intended to be serviced
and disposed by qualified Intel service personnel only.
Perchlorate Material: Special handling may apply. For more details, refer to
www.dtsc.ca.gov/hazardouswaste/perchlorate. This notice is required by California
Code of Regulations, Title 22, Division 4.5, Chapter 33: Best Management Practices for
Perchlorate Materials. This product includes a battery which contains perchlorate
material.
Taiwan battery recycling:
(Translation - please recycle batteries)
B. Additional Information
683288 | 2022.09.22
Intel
®
Agilex
™
I-Series FPGA Development Kit User Guide
Send Feedback
62

Intel Agilex I Series Specifications

General

Brand	Intel
Model	Agilex I Series
Category	Microcontrollers
Language	English

Summary

1. Overview

1.2. Box Contents

1.3. Operating Conditions

Specification of the recommended environmental and operational parameters for the development kit.

2. Getting Started

2.1. About Intel Quartus Prime Software

2.3. Installing the Intel FPGA Download Cable II Driver

3. Development Board Setup

3.1. Applying Power to the Development Board

Detailed steps for powering the development board in both PCIe-compliant and bench-top modes.

3.2. Default Switch and Jumper Settings

Explanation of the board's switch and jumper configurations and their functions.

3.3. How to Generate a POF Image to Program the Flash

Procedure for creating a Programmer Object File (.pof) for programming the flash memory.

3.4. How to Program the Generated POF Image

Step-by-step instructions for programming the generated POF image onto the development board.

3.5. The Required SmartVID QSF Assignments to Compile a Design

Necessary SmartVID QSF settings in Quartus Prime for successful design compilation.

4. Board Test System

4.1. Set Up BTS GUI Running Environment

Guide to setting up the Java environment and installing necessary components for the Board Test System.

4.1.1. Download OpenJDK

Instructions for downloading the Temurin OpenJDK, a prerequisite for the Board Test System.

4.1.2. Download OpenJFX

4.1.3. Install OpenJDK and OpenJFX

4.1.4. Run BTS GUI

4.2. Test the Functionality of the Development Kit

Overview of using the Board Test System GUI to test various functionalities of the development kit.

4.2.2. The Configure Menu

4.2.4. The GPIO Tab

4.2.5. The XCVR Tab

Performing transceiver tests, including QSFPDD, using the XCVR tab in the BTS GUI.

4.2.5.1. The QSFPDD NRZ Tab

4.2.5.2. The QSFPDD PAM4 Tab

4.2.6. The RAM Tab

4.3. Control On-board Clock through Clock Controller GUI

How to adjust on-board programmable PLL frequencies using the Clock Controller GUI.

4.4. Monitor On-board Power Regulator through Power Monitor GUI

Using the Power Monitor GUI to observe voltage, current, and temperature data.

4.5. BTS Test Areas

4.6. Identify Test Pass or Fail-based on BTS GUI Test Status

A. Development Kits Components

A.3. PCIe and CXL Interfaces

A.8. FPGA Configuration

Step-by-step guide on configuring the FPGA using the Intel Quartus Prime Programmer.

A.9. Supported Configuration Modes

A.10. Memory Interfaces

A.13. System Power

Comprehensive overview of the development board's power supply system and operating modes.

A.14. Temperature Monitoring

B. Additional Information

B.1. Safety and Regulatory Information

Essential safety, regulatory, and compliance information required for using the development kit.

B.2. Compliance Information