EasyManuals Logo

Interlogix DDV1016AM User Manual

Interlogix DDV1016AM
52 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #3 background imageLoading...
Page #3 background image
P/N 146667999-1 (ML) • REV G • ISS 19AUG19 3 / 52
10
11
12
13
14
Single zone EOL
Zone state
Value
Default
Tamper (short)
0 Ω
0 Ω
Normal
Rt
4.7 kΩ
Alarm
Rt+Ra
9.4 kΩ
Fault
Rt+Rf
14.7
AM*
Rt+Ra+Rf
19.4 kΩ
Tamper (open)
* SW2-4 must be set to On.
EN: Installation Sheet
Description
DDV1016AM(-D)(-B) is a dual AM motion sensor.
It combines the patented PIR mirror optics technology with the
patented Range Controlled Radar technology.
Installation guidelines
See Figure 1.
The detector is intended to be mounted on walls but can also
be mounted on ceilings by using a mounting bracket.
Use the following guidelines to determine the best location to
install the detector.
Mount the detector so the expected movement of an
intruder is across the detection pattern (see Figure 3).
Mount the detector at a stable surface at a height between
2.0 m and 3.0 m (6.6 and 9.8 ft.) from the floor.
Do not mount the detector within 0.5 m (1 ft. 8 in.) of
metallic objects or within 1.5 m (4 ft. 11 in.) of fluorescent
lights.
Do not place objects in front of the detector that may
prevent a clear line of sight.
Place detectors at least 6 m (19 ft. 8 in.) apart, and use
the short-range setting to avoid interference, when
mounting detectors face to face.
The dual technology processing of this detector is very
resistant to false alarm hazards. However, avoid potential
causes of instability, such as:
PIR hazards:
Direct sunlight on the detector
Heat sources within the detector field of view
Strong air draughts onto the detector
Animals in the field of view
JA
JT
3
6
4
5
Ra
Rt
JF
Rf
Fault (4)
10 9
J1
Alarm (1)
Tamper (3)
Alarm zone (2)
Off
On
Isolated fault
contact
3 resistor single
zone
(Terminal 3-10)
=
=
J1
J1
JF JT JA
2 2K
3K
4 7K
1K
2 2K
4 7K
5 6K
1K
2 2K
4 7K
5 6K
1
2
3
4
1
2
1
2
1
2
3
4
5
6
1
2
1
2
SW1 - Generic settings
LED ON
Remote OFF
Positive Polarity
LED OFF
Remote ON
Negative Polarity
Range
SW2 - AM/Fault settings
Mask to alarm and
fault relay
Auto reset
Advanced AM sens.
AM Day mode only
Mask to fault relay
only
Authorized reset
Standard AM sens.
AM Day and Night
10
3 .
m
( 3 ft )
16
52 .
m
( ft )
14
46 .
m
( ft )
12
39 .
m
( ft )
Auto Rem. Test ON Auto Rem. Test OFF
Alarm
GND
+12V
Fault
1 3
4
5
2 6
7
8 9
ON
1 2
3
4
ON
1 2
3
4
5
6
J1
JF JT JA
SW1
SW2

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Interlogix DDV1016AM and is the answer not in the manual?

Interlogix DDV1016AM Specifications

General IconGeneral
BrandInterlogix
ModelDDV1016AM
CategorySecurity Sensors
LanguageEnglish

Related product manuals