Isuzu C240 - Tightening Torque Specifications; Standard Bolts

TCM £SHoP MANUAL
TIGHTENING TORQUE SPECIFICATIONS
STANDARD BOLTS
The torque values given in the following table should be applied where a particular torque is not specified.
kg-mi(lb.f/N-m)
Bolt i
identification
Bott
diameter aT ae a
xpitch
(Low
carbon
steel)
(High
carbon
stee!)
(Alloy
steet)
(mm)
M 6x10 06 40.2 0.75 0.2 ~
( 444 14/ 5.88 1.96) | ( 5.434 1.43/ 7.354 1.96)
M 8x1.25 13 £05 1.75% 0.5 20 + 0.7
{ O44 3.4/ 12,744 4,90) | ( 12.66 3,00/ 17.15+ 490) | ( 17.36 5.36/ 19.60: 6.86)
M10 x1.25 28 £07 3.75% 0.9 50 +13
( 20.34 5.2/ 27.44% 6.86) | ( 27.204 7.2 / 36.75: 882) | ( 36.88 9.88/ 49.00 12.74)
M12 1.25 62541.2 178+ 1.5 9.65: 1.9
( 45.24 9.2/ 61.25411.76) | { 56.03 11.03/ 75.954 14,70) | ( 69.774 13.77/ 94.57+ 18.62)
M14 x15 8751.9 11.854 23 14.504 2.9
( 70.5414.5/ 85.75418.62) | ( 85.674 16.6 /116.13+ 2254) | (104.844 20.83/142.1 + 28.42)
M16 X15 133 42.7 17.304 3.5 20.40% 4.1
(94.0217.0/130.34426.46) | (125.07 25.07/169.54% 34:30) | (147.504 29.49/199.92+ 40.18)
M18 x15 192 43.8 24.90% 5.0 29.30 5.9
(138.9227.9/188.16+37.24) | (180.03 36.3 /244,02 490) | (211.844 42.83/287.14+ 57.82)
M20 x15 263 45.3 34.404 6.9 40.40% 8.1
(190.2498,2/257.74451.94) | (248.724 49.7 /337.12 6762) | (292.104 58.09/395.92+ 79.38)
M22 x15 330 +83 46,254 9.2 54.10210.8
(245,1:60.1/323.4081.34) | (934.39 66.38/453.25 90,16) | (391.15 78.14/530.184105.84)
M24 x2.0 458 49.2 58.20314.0 70.60414.1
(831.2460.2/448.84490.16) | (420.703: 102.78/570.36137.20) | (510.44:101.44/691 ,88:138.18)
"M10 X1.5 27 40.7 37 + 09 49 £12
(19.6 5.6/ 26.461 6.86) | ( 26.75% 6.7 / 36.26: 882) | ( 35.434 8.42/ 48,024 11.76)
oz x15 58 £12 72214 91 + 18
(42.04 9.0/ 56.84411.76) | ( 52.02+ 10.05/ 70.56% 13.72) | ( 65.804 12.80/ 89.18 17.64)
M14 2.0 91 418 112 £ 22 136 + 27
( 65.8112.8/ 89.18117.64) | ( 80.974 15.7 /109.76+ 21.56) | ( 98.334 19.33/133.28+ 26.46)
M16 x20 127 42.5 165 + 33 195 + 39
(91.9417.9/124.46+24.5 ) | (119.304 24.3 /161.70+ 32.34) | (140.994 27.99/191.1 + 38.22)
Note:
The astarisk (*) indicates that the bolts are used for female-threaded parts that are made of soft mate-
rials such as cas