Jackson Conserver AXL

Questions and Answers

J
Jamie CoxSep 9, 2025
How to troubleshoot a Jackson Conserver AXL Laboratory Equipment sanitizer pump that doesn't run?
- T
  Tina VasquezSep 9, 2025
  If the sanitizer pump on your Jackson Laboratory Equipment doesn't run during the cycle or when using the prime switch, check for a loose motor terminal wire and tighten the connections. If the connections are secure, the sanitizer pump motor might be faulty. If you read 120V at the sanitizer motor terminals during the sanitizer feed cycle, replace the motor.
J
James AguilarSep 8, 2025
What to do if Jackson Laboratory Equipment machine will not run in 'ON' position or in Delime mode?
- K
  Kevin AdamsSep 8, 2025
  If your Jackson Laboratory Equipment machine won't run in either the 'ON' position or in Delime mode, a faulty OFF/ON/FILL switch could be the cause. With the switch ON, check the voltage between the BLACK and WHITE/BLACK wires on the switch and replace it if you find 120V. Alternatively, a faulty NORMAL/DELIME switch might be the problem; in the NORMAL position, check the voltage between the WHITE/BLACK & WHITE/RED wires to the switch and replace it if you find 120V.
A
Ariel PhamSep 6, 2025
Why is the wash motor running continuously on my Jackson Conserver AXL Laboratory Equipment?
- V
  Valerie WilsonSep 6, 2025
  If the wash motor is running continuously on your Jackson Laboratory Equipment, first check if the NORMAL/DELIME switch is in the Delime position and place it in the Normal position. Another cause could be that the wash relay contacts are welded closed; turn the machine off, and if the wash relay doesn't release, replace the contactor. Additionally, the cam timer might be stalled in the wash or rinse cycle; if the cam timer isn't rotating, check the voltage to the timer motor, and if there's no voltage when the door is closed, check the wires and/or replace the motor. Lastly, a faulty wash motor microswitch could be the issue; tighten connections, make sure the switch makes contact, and replace it if necessary.
S
Shannon SwansonSep 2, 2025
What causes a Jackson Laboratory Equipment machine to fill continuously even with no power?
- J
  James TaylorSep 2, 2025
  If your Jackson Laboratory Equipment machine fills continuously even when no power is applied, the solenoid valve is likely dirty or faulty. Try cleaning the valve, and if that doesn't work, replace the plunger and/or diaphragm.
B
Brandi BarronSep 1, 2025
What to do if Jackson Conserver AXL Laboratory Equipment machine will not run, no voltage at wash relay terminals L1 and T1?
- H
  Heather AtkinsonSep 1, 2025
  If your Jackson Laboratory Equipment dishmachine won't run and there's no voltage at the wash relay terminals L1 and T1, first ensure the service disconnect switch is on. If it is faulty, turn disconnect on. Also, check if the branch circuit breaker has tripped or a fuse has blown; reset or replace as needed. Finally, inspect for loose or broken connections to the dishmachine and tighten or replace them.
T
Thomas AguirreAug 30, 2025
How to troubleshoot a Jackson Conserver AXL Laboratory Equipment wash motor that does not run?
- R
  robert45Aug 30, 2025
  If the wash motor in your Jackson Laboratory Equipment doesn't run unless the wash relay is manually depressed, but other functions work, a faulty control relay could be the cause. Check the voltage across relay contacts #7 & #4; if it reads 120V during the wash cycle, replace the relay. Another possibility is a faulty wash relay. Check voltage at relay coil between ORANGE/BLACK and WHITE wires. If you read 120V, coil is faulty. Replace the relay.
S
Samantha PetersonAug 29, 2025
Why is my Jackson Conserver AXL machine cycling continuously?
- M
  Michelle HartAug 29, 2025
  If your Jackson Laboratory Equipment machine is cycling continuously, the cycle reset switch might be loose; try repositioning the switch assembly and bending the metal lever if necessary. Alternatively, the cycle reset switch could be faulty; measure between the BLACK/YELLOW & ORANGE wires on 'cycle reset' switch while timer is rotating. As the switch lever drops into home position you should measure 120V. If not, adjust or replace the switch.
L
Leslie GrahamAug 27, 2025
How to resolve low pumped water pressure in Jackson Laboratory Equipment?
- J
  Jimmy WalkerAug 27, 2025
  If you're experiencing low pumped water pressure in your Jackson Laboratory Equipment, it could be due to an obstruction in the pump housing or wash manifold; disassemble and clear any blockages. Alternatively, the pump impeller might be worn or broken, requiring replacement.