janitza UMG 604-PRO - Page 5

janitza UMG 604-PRO

87 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

www.janitza.de

UMG 604-PRO

IV

19. Dimension diagrams 77

19. 1 Front view 77

19. 2 Side view 78

20. Connection example 79

21. Short introduction (setting primary current) 81

Table of Contents

Default Chapter2
- Table of Contents2
Table of Contents6
General6
- Disclaimer6
- Copyright Notice6
- Technical Changes6
- Declaration of Conformity6
- Comments on the Manual6
- Meaning of Symbols6
Safety8
- Safety Information8
- Safety Measures9
- Qualified Staff9
Proper Use10
- Inspection on Receipt10
- Scope of Delivery11
- Available Accessories11
Product Description12
- Measuring Process12
- Network Failure Detection12
- Usage Concept12
- Gridvis® Network Analysis Software12
- Features13
- Product Overview14
- Installation Location15
Network Systems16
- Three-Phase 4-Conductor Systems17
- Three-Phase 3-Conductor Systems17
- Rated Voltages18
Installation20
- Disconnectors20
- Supply Voltage20
- Measured Voltage21
- Current Measurement22
- Connection Variants24
- Temperature Measurement27
Interfaces28
- Shielding28
- Rs23229
- Rs48529
  - Cable Type30
  - Termination Resistors30
- Bus Structure31
- Profibus32
  - Connection of the Bus Wiring32
Digital Inputs and Outputs34
- Digital Inputs34
- S0 Pulse Input35
- Digital Outputs36
Commissioning38
- Connecting the Supply Voltage38
- Frequency Measurement38
- Connecting the Measured Voltage38
- Phase Sequence38
- Applying the Measured Current39
- Checking the Power Measurement39
Operation40
- Button Functions40
- Display Mode40
- Programming Mode41
- Display Password41
- Homepage Password41
Configuration42
- Current Transformer Ratio42
- Current Connection Variants42
- Voltage Transformer Ratio43
- Voltage Connection Variants43
- RS232 Configuration44
- RS485 Configuration44
- Ethernet Configuration45
- Profibus Configuration46
- Recording Configuration50
- PTP Configuration52
  - 11.10.1 Important Modbus Parameters for the PTP Configuration of the Device52
  - 11.10.3 Example: PTP Timing According to IEEE 1588-2008 and Clock Types53
System Information54
- Measurement Range Exceeded54
Device Homepage56
- Measured Values57
- Power Quality61
- Apps62
  - 13. 3. 1 Push Service62
- Information63
Service and Maintenance64
- Repair and Calibration64
- Front Film64
- Disposal64
- Service64
- Battery64
- Firmware Update64
Procedure in the Event of Faults66
Technical Data68
- General68
- Environmental Conditions68
- Transport and Storage68
- Supply Voltage69
- Protection Class69
- Digital Inputs and Outputs70
- Temperature Measurement Input71
- Voltage Measurement Inputs72
- Current Measurement Inputs72
- Interfaces73
- Measurement Uncertainty74
Parameter List76
Measured Value Indications80

Other manuals for janitza UMG 604-PRO

Installation Instructions14 pages

Related product manuals

Preview: janitza UMG 604

janitza UMG 604

Preview: janitza UMG 96S

janitza UMG 96S

Preview: janitza UMG 104

janitza UMG 104

Preview: janitza UMG 804

janitza UMG 804

Preview: janitza UMG 511

janitza UMG 511

Preview: janitza UMG 500 A

janitza UMG 500 A

Preview: janitza UMG 96-S2

janitza UMG 96-S2

Preview: janitza UMG 96RM-P

janitza UMG 96RM-P

Preview: janitza UMG 509-PRO

janitza UMG 509-PRO

Preview: janitza UMG 512-Pro

janitza UMG 512-Pro

Preview: janitza UMG 96 RM-E

janitza UMG 96 RM-E