– 40 –
No. Item name Input range
S017 The number of stitches to
be sewn on the multi-lay-
ered section
0 to 200
stitches
-
This data item is used for setting the number of stitches
to be sewn from the time at which the presser foot runs
on the multi-layered section to the time at which the
presser foot leaves the multi-layered section. While the
sewing machine is engaged in sewing of this number of
stitches, the sewing machine operates using the presser
foot pressure set with "S018", the cloth pulling amount
set with "S019" and the cloth puller pressure set with
“S020”.
S018
*2
Presser foot pressure for
sewing the multi-layered
section
–
350 to
200 -
S019 Cloth pulling amount for
sewing the multi-layered
section
1.2 to
5.5mm
-
S020
*3
Cloth puller pressure for
sewing the multi-layered
section
–
90 to
160 -
S021
Multi-layered section
changeover OFF sensor
value
500 to 3000
Multi-layered
section is
not detected
- When the multi-layered section sensor value falls below
this value while the sewing machine is engaged in the
sewing of the multi-layered section of material, the
sewing machine nishes the sewing of the multi-layered
section. This set value is rendered effective in the case
the number of stitches for multi-layered section (S017)
is not set (0 stitch).
S031
*
1
Sewing speed for starting
sewing of the top end of
material
150 to 5500sti/min
This data item is used for setting the sewing speed to
be employed when the material is detected after the
state no material has been detected. In the case a cloth
sensor is not used, the speed limit by this parameter will
not be applied. In the case both this function and "U037
Soft start function" are enabled, the sewing machine will
operate using the lower sewing speed.
S032
*
2
Presser foot pressure for
starting sewing of the top
end of material
–
350 to 200
This data item is used for setting the presser foot pres-
sure to be applied when the material is detected after
the state no material has been detected.
S033
Number of stitches for
changing the sewing
speed for starting sewing
of the top end of material
0 to 200 stitches
This data item is used for setting the number of stitches
to be sewn with the sewing speed set with "S031 Sewing
speed for starting sewing of the top end of material".
S034
Number of stitches for
changing the presser
foot pressure for starting
sewing of the top end of
material
0 to 200 stitches
This data item is used for setting the number of stitches
to be sewn with the sewing speed set with "S032 Sewing
speed for starting sewing of the top end of material".
S041
Number of stitches to be
sewn from the beginning
of sewing until the chain-
off thread cutter is actuat-
ed
0 to 2000 stitches
This data item is used for setting the number of stitches
to be sewn from the time at which the material is detect-
ed to the time at which chain-off thread cutter is actuat-
ed.
*1: The actual sewing speed is limited by "S003 Stitch length" and the set value of cloth pulling amount.
In the case the set value of stitch length is 3.1 mm or more: Maximum sewing speed 5000 sti/min
In the case the set value of cloth pulling amount is 4.6 mm or more: Maximum sewing speed 4000 sti/min
*2: If this value is set to a negative value (minus value), the presser foot will go up. If the presser foot height is set so
that it oats, the multi-layered section changeover function will be disabled.
*3: If this value is set to a negative value (minus value), the cloth puller will go up.
To Next Page
Loading...
Need help?
General
