JVC DX-MX70BK User Manual

~ DX-MX70BK |
Recording CD Tracks in
Auto-Edit Mode
In Auto-Edit mode, tracks from the CD will automatically be selected to
determine which tracks should go on side A of the tape and which should
go on side B.
The selection is based on the lengths of the tracks and the iength of the
tape. This ensures a proper ‘’fit’’ of the tracks recorded on the tape. It
prevents a track from being cut off when the end of the tape is reached.
. Insert the cassette for recording in deck B.
@ Set the REV. MODE switch to the Auto reverse > position if you
want to record on both sides of the cassette.
. Put the CD in the CD Player.
Press the STOP/CLEAR button on the CD Player.
Press the A. EDIT button on the CD Player to tell the system the length
of the tape in the Tape Deck.
Amr
™ The tape length most suitable for CD recording is displayed first.
@ Each time the A.EDIT button is pressed, the next standard tape length
blinks, in this order:
> C46 C54 C60P C74 C90P (back to the beginning)
® You can also enter a non-standard tape length from the Remote Con-
troller using the numeric keys.
For example: To enter a tape length of 50 minutes, press the CD 1OKEY
button on the Remote Controller, then press the + 10 key four times and
the 10 key once.
. Press the SIDE A/B button on the Remote Controller.
@ The CD Player calculates which tracks should be placed on side A and
which should be placed on side B, based on the lengths of the tracks
and the length of the tape.
@ If you do not press the SIDE A/B button, the CD Player automatically
decides which tracks should be placed on sides A and B about 4
seconds after the A. EDIT button is pressed.
Note: Up to 16 tracks can be allocated for each side of the cassette.
- Press the CD DIRECT REC button on the Tape Deck.
@ The tape is automatically rewound to the beginning of side A, and then
recording begins.
™@ When the Tape Deck is set in the auto reverse mode, after the last
track is recorded on side A, the tape deck high-speed-erases to the
end of side A. Then it changes direction to side B and begins record-
ing the remaining tracks.
™
To
stop
recording,
press
the
Stop
®
button
on
deck
B,
or
press
the
STOP/CLEAR
button
on
the
CD
Player.
Hse
During
recording
in
the
Auto-Edit
Mode,
do
not
operate
the
CD
layer.
Recording CD Tracks in
Programmed-Edit Mode
In Programmed-Edit Mode, you decide which tracks from the CD will be record-
ed, and in what order.
1.
Insert the cassette for recording in deck B.
® Set the REV. MODE switch to the Auto reverse &> position if you
want to record on both sides of the cassette.
. Put the CD in the CD Ptayer.
. Press the STOP/CLEAR button on the CD Player.
. Press the PROG. EDIT button on the Remote Controller to tell the sys-
_ tem the length of the tape in the Tape Deck.
Cc
@ Each time the PROG. EDIT button is pressed, the next standard tape
length blinks, in this order:
» C46 Bm C54 & C60 & C74 & C90 P (back to the beginning)
@ You can enter a non-standard tape length from the Remote Controller
using the numeric keys.
For example: To enter a tape length of 50 minutes, press the CD 10KEY
button on the Remote Controiler. Then press the + 10 key four times and
the 10 key once.
. Press the SIDE A/8 button on the Remote Controller.
SIDE AB
& This telis the system that you will be choosing tracks to be recorded
on side A of the tape.
@ The iength of time for one side of the tape is displayed. This is half
of the total tape length. The total time for the tracks you choose for
each side cannot exceed this time.
® If you do not press the SIDE A/B button, side A is automatically selected.
. Press the CD 10KEY button on the Remote Controller.
. Enter the numbers of the tracks you want recorded on one side of the
tape.
™
Tracks
on
a
CD
assigned
numbers
32
or
greater
cannot
be
entered
in
the
program.
@ If the length of a track exceeds the remaining tape length, the time
indication blinks on the display. Choose a different track number.
® To delete a track from the program, specify the track with the AUTO
SEARCH buttons on the Remote Controller. Then press the CAN CEL
button on the Remote Controller.
. Hf you also want to record on the other side of the tape, press the SIDE
A/B button on the Remote Controller and repeat step 7.
. Press the CD DIRECT REC button on the Tape Deck.
17

JVC DX-MX70BK Specifications

General

Brand	JVC
Model	DX-MX70BK
Category	Stereo System
Language	English