JVC DX-MX70BK User Manual

_ DX-MX7OBK |
Setting the Stop Time
1. Press the TUNING/TIMER/DIMMER buttons to set the hour that the
system will turn off.
2. Press the MEMORY button.
This stores the hour portion of the stop-time in memory.
3. Press the TUNING/TIMER/DIMMER buttons to set the minute.
4. Press the MEMORY button.
This
stores
the
minute
portion
of
the
stop
time
in
memory.
Selecting the Source
1. Press the TUNING/TIMER/DIMMER button to select a source.
Repeatedly pressing the > button displays the sources in the following
order:
Display What it means
wont Plays from whichever source was used just before
turning off the system
TUNER Plays FM or AM broadcast
TUNER TIMER REC Records FM or AM broadcast
cD Plays a CD
TAPE Plays a tape
-- --TIMER REC Records from whichever source was used just be-
fore turning off the system
Note: If you choose an FM or AM radio station as the source, select the
preset station by pressing the PRESET button on the Tuner.
2. Press the MEMORY button.
This stores the source to play or record in memory.
Setting the Volume
1. Press the TUNING/TIMER/DIMMER button to select a volume level.
Repeatedly pressing the > button displays the volume levels in the fol-
lowing order:
Display What it Means
VOL -- -- Volume set to the level used before shut the power off.
VOL --0 Volume off
VOL --A Volume barely on
VOL --B Volume at 1/4 power
VOL --C Volume at 1/3 power
2. Press the MEMORY button.
This stores the volume level for timed playback or recording in memory.
Starting the Timer
Press
the
Timer
button
to
start
the
timer.
The
timer
you
chose
should
tight
on
the
display.
Note:
!f
the
timer
light
does
not
light,
the
timer
was
not
set
properly,
and
yOu
N€ed
to
set
the
start
time
again.
To
change
your
selection,
press
the
CANCEL
button
and
enter
a
new
value.
Turning the System Off
Press the POWER button on the Amplifier to turn the system off.
©
® The system is now programmed to turn on at the preset start-time,
and play or record until the stop-time.
® It will record or play the preset source at the preset volume level until
the stop-time is reached.
® If you turn the system on before the start-time, the timer will still Oper-
ate as programmed at the start-time.
Resetting the Timers
To reset a timer, press the button (TIMER1, TIMER2, or DAILY) on the
Tuner
twice.
Now
the
timer
is
set
again
and
will
use
the
same
start-time,
stop-time, source, and volume level as before.
Setting the Wake-Up and Sleep Timers
You can set a timer so it turns on to wake you up or turns off when you
go to sleep.
Setting the Wake-Up Timer
The wake-up timer serves as an alarm clock. It turns the system on after
a programmed time lapse and plays the source that was used before the
system was turned off. You can set a wake-up time from between 5
minutes and 12 hours.
1. Press the POWER switch on the Amplifier so it is off.
2. Press the WAKE UP/SLEEP button on the Tuner.
(mee eran
This tells the system that you are going to set the wake-up time.
3. Press the WAKE UP/SLEEP button repeatedly until the desired wake-
up time appears.
Each time you press the WAKE UP/SLEEP button, the wake-up time lapse
changes in the following order:
0:05 0:10 0:15-0:30 0:45 1:00 1:30 2:00 3:00P (every
hour) » 12:00® (back to the beginning)
® If you make a mistake, press the CANCEL button on the Tuner and
enter a new wake-up time with the WAKE UP/SLEEP button.
The system will now turn on after this time lapse.
@ The wake-up timer has priority over TIMER1, TIMER2, and the DAILY
timer.
This means that if the start-time for one of the timers occurs before
the wake-up time, the system will wait until the wake-up time to turn on.
Note: If CD is the source that will be used, playback begins with the first
track.
21

JVC DX-MX70BK Specifications

General

Brand	JVC
Model	DX-MX70BK
Category	Stereo System
Language	English