1-16 (No.HC044<Rev.001>)
4.2.4 Camera Adjustment
No. Item
Measuring
Instrument &
Input Signal
Mode
Measuring Point (A)
Adjustment Point (B)
Adjustment Level (C)
Adjustment Procedure
1 White Drop
Out Pixel of
CCD
--- Internal temper-
ature of the unit
is 47.5°C or
higher (43h or
less)
(A)HDMI output
(B)2000h to 3FFFh
(C)Automatic adjustment
(1) Apply power to the unit for more than 60
minutes, then check the internal tempera-
ture is 47.5°C or higher (43h or less) using
the SSS.
(2) Start the adjustment.
(3) When the adjustment is completed, the in-
formation screen shows the completion of
the adjustment.
(4) Before checking the white blemish, unplug
the power cord and plug it back in.
NOTE
• For white blemish detection, the CCD must be fully warmed up.
- White blemish cannot be detected when the CCD is cold.
- Apply power for more than 60 minutes, then check the internal temperature is 47.5°C or higher (EEPROM data : 43h or
less) with the SSS main screen [Option]→[About Temperature(OP)].
- When the room temperature is low, the CCD may not be fully warmed up. Warm up the internal temperature by wrapping
the unit with antistatic aircap or similar material.
• Inserting an SD card to slot A is required.
(An SD card is required to temporary store the white blemish data obtained from the CCD. When the adjustment is finished,
the data is written in the EEPROM, and the temporary data on the SD card is deleted.)
• Before checking the white blemish correction, unplug the power cord and plug it back in.
(The adjustment only writes the correction data, and actual correction data reading and correction is performed when the
power is turned ON.)
2 Hall gain,
Offset
--- EE/Video mode
(A)---
(B)60 Hz(NTSC)
:12C0h,12C1h
136Ah,136Bh
50 Hz(PAL): 62C0h,62C1h
636Ah,636Bh
(C)Automatic adjustment
• Adjust in 60 Hz(NTSC), the value is also writ-
ten in the 50 Hz(PAL) address.
(1) Start the adjustment.
(2) When the adjustment is normally finished,
the information screen shows the comple-
tion of the adjustment. The color bar is dis-
played in the unit.
3 ND Hall
gain, Offset
--- EE/Video mode
(A)---
(B)60 Hz(NTSC):1330h,1331h
4102h,4103h
50 Hz(PAL): 6330h,6331h
7102h,7103h
(C)Automatic adjustment
• Adjust in 60 Hz(NTSC), the value is also writ-
ten in the 50 Hz(PAL) address.
(1) Start the adjustment.
(2) When the adjustment is normally finished,
the information screen shows the comple-
tion of the adjustment. The color bar is dis-
played in the unit.
4 White bal-
ance
• Light box
• Collimator
•Filter
(Color temper-
ature conver-
sion LBB12)
EE/Video mode
(A)---
(B) 60 Hz(NTSC)
:122Ah~1239h
50 Hz(PAL): 622Ah~6239h
(C)Automatic adjustment
• Adjust in 60 Hz(NTSC), the value is also writ-
ten in the 50 Hz(PAL) address.
(1) Attach the collimator (without chart) to the
camera lens.
(2) Shoot the light box.
(3) After the start of the adjustment, the ad-
justment on the low color temperature is
completed, and the confirmation screen
for the continuing adjustment is displayed.
(4) Attach the LBB12 filter, then click OK.
(5) Start the adjustment.
(Adjustment on high color temperature
starts.)
(6) When the adjustment is normally finished,
the information screen shows the comple-
tion of the adjustment. The color bar is dis-
played in the unit.
To Next Page
Loading...
