Why is the recording time shorter than expected on my JVC GY-HM180U Camcorder?
If the actual recording time on your JVC Camcorder is shorter than the estimated time, be aware that the recordable time may be shorter depending on the shooting conditions or the subject.
How to fix a JVC GY-HM180U when the power does not turn on?
If your JVC Camcorder's power does not turn on, consider these potential solutions: * Ensure the AC adapter is properly connected. * Verify the battery is charged. * If the power was recently turned off, wait at least 5 seconds before attempting to turn it on again.
Why can't I connect my JVC Camcorder to wireless LAN?
If you cannot connect your JVC Camcorder to a wireless LAN, consider the following: * Check the connection mode and settings, specifically the [SSID] and [Passphrase] if not using WPS. * If the Passphrase is incorrect, re-enter it, even if a “Completed the Setup Wizard” message appears.
What to do if the camera image is not output on the LCD monitor and viewfinder screen of my JVC GY-HM180U Camcorder?
If the camera image is not displaying on the LCD monitor and viewfinder screen of your JVC Camcorder, make sure the camera recorder is set to the Camera mode by using the [MODE] selection button.
What causes the View Remote screen issues on my JVC GY-HM180U Camcorder?
If The View Remote screen turns black, flickers, freezes, or you cannot perform remote operation on your JVC Camcorder, the network path may be congested. Wait a while before refreshing (reloading) the web browser.
Why is the wireless LAN disconnected on my JVC GY-HM180U Camcorder?
If the wireless LAN on your JVC Camcorder is disconnected, the following suggestions may help: * The wireless LAN may be disconnected depending on the environment. Try changing the usage environment. * Try connecting via wired LAN.
Why is there an incorrect display on the viewfinder of my JVC Camcorder?
If you're experiencing an incorrect display on the viewfinder of your JVC Camcorder, check if [LCD/VF] B [VF SW] is set to “Enable” and if the viewfinder is in use without being pulled out. To use the viewfinder in this setting, pull out the viewfinder.
How to fix JVC GY-HM180U Camcorder SD card that cannot be initialized?
If the SD card of your JVC Camcorder cannot be initialized (formatted), ensure that the write-protect switch on the SD card is turned off.
Why does the wireless LAN disconnect on my JVC Camcorder?
If your JVC Camcorder's wireless LAN keeps disconnecting, consider these points: * The disconnection could be due to the environment; try changing your usage environment. * As an alternative, connect via a wired LAN.
What to do if my JVC Camcorder is unable to start recording?
If you're having trouble starting a recording on your JVC Camcorder, here's what to check: * Make sure the record trigger button/lock switch on the handle is turned on. * Ensure the write-protect switch on the SD card is off. * Verify the camera recorder is set to Camera mode using the [MODE] selection button. * Confirm the inserted SD card is compatible with the recording format.
General| Effective Pixels | 12.4 MP |
|---|---|
| Optical Zoom | 23x |
| Video Resolution | 1920 x 1080 (HD), 720 x 480 (SD) |
| Focal Length | 4.1mm - 53.3mm |
| Maximum Aperture | f/1.8 - f/2.8 |
| Display Type | LCD |
| Screen Size | 3.5 inches |
| Lens Mount | Fixed |
| LCD Screen Size | 3.5 inches |
| Microphone | Built-in stereo microphone |
| HDMI Output | Yes |
| Battery Type | Lithium-ion |
| Recording Format | MP4 |
| Frame Rate | 30p, 24p |
| Storage | SDHC/SDXC |
| ND Filter | Yes (1/4, 1/16, 1/64) |
| Recording Media | SD/SDHC/SDXC card |
| Video Format | MPEG-2 (HD), MPEG-4 AVC/H.264 (SD) |
| Audio Input | 3.5mm stereo mini jack |
| Interfaces | HDMI, USB 2.0 |
| Audio Format | Dolby Digital 2ch |
| USB Interface | USB 2.0 |
| Audio Recording | 2-channel PCM |
| Resolution | 920, 000 dots |
| LCD Resolution | 920, 000 dots |
To Next Page
