Why doesn't the [CH1/CH2] recording level adjustment knob work on my JVC Camcorder?
If the [CH1/CH2] recording level adjustment knob on your JVC Camcorder does not work, check if the [CH1/CH2 AUTO/MANUAL] switch is set to “AUTO”. Also, verify if the [FULL AUTO] switch is set to “ON” and [A/V Set] B [Audio Set] B [Audio On FULL AUTO] is set to “Auto”.
What to do if my JVC Camcorder won't start recording?
If your JVC Camcorder isn't recording, make sure the record trigger button/lock switch on the handle is turned on. Check if the SD card's write-protect switch is enabled; if so, turn it off. Verify that the camera recorder is set to Camera mode by using the [MODE] selection button.
How to fix a JVC Camcorder if the power does not turn on?
If your JVC Camcorder isn't powering on, ensure the AC adapter is properly connected and the battery is adequately charged. Also, avoid immediately turning the power back on after switching it off; wait at least 5 seconds before attempting to power it on again.
Why is the GPS position not accurate on my JVC GY-HM650U?
The precision error on your JVC Camcorder may be up to hundreds of meters if the GPS signal is weak or reflected off surrounding buildings.
How to display the time code and user’s bit on JVC Camcorder?
The time code and user’s bit may not be displayed on your JVC Camcorder depending on the display type, even in Camera or Media mode. Also, check if [LCD/VF] B [Display Settings] B [TC/UB] is set to “Off”. To display them, set it to “TC” or “UB.”
Why is there an incorrect display on the viewfinder of my JVC GY-HM650U Camcorder?
If there is an incorrect display on the viewfinder of your JVC Camcorder, check if the LCD monitor is used with [LCD/VF] B [LCD + VF] set to “Off”.
Why are my JVC Camcorders not synchronized after synchronizing time codes?
If two JVC Camcorders are not synchronized even after synchronizing time codes, verify that the [TC IN/OUT] switch is correctly set. Also, ensure that [System] B [Record Set] B [Record Format] B [WFrame & Bit Rate] is set so that both camera recorders have the same frame rate.
Why is the display on my JVC Camcorder viewfinder incorrect?
If the display on your JVC Camcorder's viewfinder is incorrect, check if the LCD monitor is used with [LCD/VF] B [LCD + VF] set to 'Off'.
Why is the actual recording time shorter than the estimated time on my JVC Camcorder?
The recordable time on your JVC Camcorder may be shorter than estimated depending on the shooting conditions or the subject.
Why is there no sound when playing back clips on my JVC GY-HM650U?
If there's no sound during playback on your JVC Camcorder, it could be because the clip was recorded in Variable Frame Rec mode.
General| Video Resolution | 1920 x 1080 |
|---|---|
| Audio Channels | 2 |
| HDMI Output | Yes |
| Component Output | Yes |
| Composite Output | Yes |
| FireWire | No |
| Image Stabilization | Optical |
| Filter Size | 72 mm |
| Camera Type | Professional |
| Sensor Type | 3x 1/3" CMOS |
| Effective Pixels | Approx. 2.07 megapixels (1920 x 1080) |
| Recording Format | AVCHD |
| Maximum Aperture | f/1.6 |
| Minimum Focus Distance | 1 m |
| ND Filter | Yes (1/4, 1/16) |
| Recording Media | SD/SDHC/SDXC |
| Audio Format | Linear PCM |
| LCD Screen | 3.5-inch |
| Viewfinder | 0.45" |
| Microphone Input | Yes, 2x XLR |
| Headphone Output | Yes, 1x 3.5mm |
| USB | Yes |
| Wireless | Optional |
| Battery Type | Lithium-ion |
| Battery Life | Approximately 3 hours with BN-VF823 |
| Frame Rate | 50i, 25p |
To Next Page
