(No.HC034<Rev.001>)1-23
5.1.3 Firmware version display
(1) Refer to 5.1.2.1 to display the VERSION MENU.
(2) The program number and version of the firmware package
are displayed.
5.1.4 VERSION CHECK Display
(1) Refer to 5.1.2.2 to display the ADVANCED MENU.
(2) Move the cursor to [VERSION CHECK], then press the
[Set] button or the [Cross-Shaped] button (right).
(3) The numbers and versions of each program are displayed.
5.1.5 ADVANCED FUNCTION Menu operation
(1) Refer to 5.1.2.2 to display the ADVANCED MENU.
(2) Move the cursor to [ADVANCED FUNCTION], then press
the [Set] button or the [Cross-Shaped] buttons (up/down) to
change the parameter.
(3) ADVANCED FUNCTION Menu is displayed.
(4) Move the cursor to the item to be changed, then press the
[Set] button or the [Cross-Shaped] button (right).
(5) The parameter blinks. Press the [Cross-Shaped] buttons
(up/down) to change the parameter.
(6) Press the [Set] button to set the parameter. The parameter
lights up.
(7) Move the cursor to [BACK], then press the [Set] button or
the [Cross-Shaped] button (right) to go back to the upper
layer and finish the setting.
(Bold is the factory setting.)
*1 The lens iris is set to the auto mode by automatically at the
followings.
(1) When the iris is operated by the RM controller.
(2) When the GAIN, the IRIS and the SHUTTER are setting
to the auto mode.
*2 Available only when the Camera Resolution setting is
1280x720, and the Frame & Bit Rate setting is 60p(HQ) or
60p(SP). Otherwise, [---] is displayed and no selection is
available.
*3 When only recording to the SDHC memory cord, this func-
tion is available.
5.1.5.1 White blemish detection
(1) Open the User Menu, then set [Camera Resolution] in
[Record Format] to 1280x720, and [Frame & Bit Rate] to
60p(HQ) or 60p(SP).
(2) Open the ADVANCED FUNCTION Menu, change the [PIX-
EL COMPEN DET] parameter to [EXECUTE], and then
press the [Set] button.
NOTE :
• To cancel the parameter setting change, press the [CAN-
CEL] button or the [Cross-Shaped] button (left) while the
parameter is blinking.
--- VERSION ---
FIRMWARE SPL V
EXIT
--- VERSION CHECK ---
SYS CPU SPL2188 V
CAM CPU SPL2189 V
MBE CPU SPL2190 V
MBE LOADER SPL2191 V
FPGA8 SPL2192 V
FPGA9 SPL1036 V
FPGA10 SPL1037 V
FPGA11 SPL2195 V
EXIT
--- ADVANCED FUNCTION ---
IRIS ENF AUTO ON
PIXEL COMPEN DET CANCEL
AE DETECT PEAK 10
FAW SENSITIVITY FAST
BATT. DISPLAY AUTO
C.REC AUDIO FADE ON
LOOP REC OFF
SDI OUT..
BACK
Item Parameter
IRIS ENF.
AUTO
OFF While in the FULL AUTO mode,
the IRIS mode depends on the
lens IRIS MODE switch setting.
ON While in the FULL AUTO mode,
the Auto Iris mode is activated
even the Manual Iris mode is se-
lected.*1
PIXEL
COMPEN DET
*2
CANCEL Does not execute blemish detec-
tion.
EXECUTE Executes blemish detection.
AE DETECT
PEAK
10 Sets the VIDEO PEAK ratio for AE
control. 0 to 50 (By 5%)
FAW
SENSITIVITY
SLOW
MIDDLE
FAST
Sets the response speed of the
FAW control.
BATT. DISPLAY OFF Does not display the battery infor-
mation.
AUTO Follow the BATTERY INFO
MENU setting.
C.REC AUDIO
FADE*3
OFF No AUDIO FADE in STBY↔REC.
ON AUDIO FADE in STBY↔REC.
LOOP REC OFF No LOOP REC.
ON Endless LOOP REC.
SDI OUT.. Refer to the 5.1.5.2
Record Format
File Format Quick Time
Camera Resolution 1280x720
Frame & Bit Rate 60p(HQ)
Back
To Next Page
Loading...
