JVC LT-32D200 User Manual

43
EN
INTRODUCTION
PREPARATION
WATCHING TV
OPTIONAL SETTING OPERATING DVD
DVD SETTING
TROUBLESHOOTING INFORMATION
English
Stereo Sound Mode
Stereo Sound Mode
CD
This unit allows you to select a sound mode during CD playback.
During playback, press [AUDIO] repeatedly until the
desired sound mode appears.
STEREO
• Each time you press [AUDIO], the sound mode
changes as example below.
STEREO (stereo sound with left and
right channels)
L-ch (left channel sound only)
R-ch (right channel sound only)
Note:
• Virtual surround cannot be changed when the sound mode
is set to either “L-ch” or “R-ch”.
Virtual Surround
Virtual Surround
You can enjoy virtual surround on your 2 channel stereo system.
1
During playback, press [MODE] repeatedly until “ ”
appears.
OFF
(
SURROUND
)
2
Press [Cursor K / L] to select the sound level.
1
(
SURROUND
)
1 : Natural effect.
2 : Emphasized effect.
OFF : No effects (original sound).
3
Press [BACK] to exit.
Note:
• The setting will be kept even if the unit is turned off.
• For audio CD, virtual surround will not be effective if the
sound mode is set to something other than “STEREO”.
(Refer to “Stereo Sound Mode” on page 43.)
• Turn down the level or select “OFF” if the sound is distorted.
Marker Setup
Marker Setup
This feature allows you to assign a specific point on a disc to be called back later.
To set a marker
1
During playback, press [MODE] repeatedly until
“ ” / “ ” appears.
e.g.) DVD
_ _ /12 (SEARCH)
2
Use [Cursor K / L] repeatedly until marker search
menu appears.
123456789 10 AC
3
Use [Cursor s / B ] to select an available marker within
60 seconds.
123456789 10 AC
4
When the playback reaches the point at which you
want to set a marker, press [ENTER].
• Marker is now set.
23456789 10 AC
5
Press [BACK] to exit.
To return to the marker later
1
Repeat steps 1-2 in “To set a marker”. Use [Cursor s / B ]
to select the desired marker.
e.g.) DVD
23456789 10 AC
2
Press [ENTER] at the desired marker to restart playback
from the specific point which you set.
23456789 10 AC
Note:
• Marker search menu will disappear in about 60 seconds
when there is no input.
• You can mark up to 10 points.
• To clear a marker, select the marker to be cleared, and then
press [CLEAR].
• Ejecting the disc or turning off the power will erase all
markers.
• Selecting “
” at step 3 in the section “To set a marker” will
also erase all markers.

JVC LT-32D200 Specifications

General

HD type	Not supported
Display diagonal	32 \
Display brightness	360 cd/m²
Display technology	LCD
Native aspect ratio	16:9
Contrast ratio (typical)	1200:1
Screen format adjustments	4:3, 16:9
Power requirements	120V, 60HZ
Operating temperature (T-T)	5 - 40 °C
RMS rated power	20 W
Number of speakers	2
Equalizer bands quantity	5
Image formats supported	JPG
Optical disc player type	DVD player
Digital audio coaxial out	1
Component video (YPbPr/YCbCr) in	3
Product color	Black
Panel mounting interface	200 x 100 mm
Power consumption (typical)	160 W
Tuner type	Analog & digital

Weight and Dimensions

Depth (with stand)	234 mm
Width (with stand)	760 mm
Height (with stand)	563 mm
Weight (with stand)	9800 g
Depth (without stand)	127.5 mm
Height (without stand)	519.3 mm
Weight (without stand)	9300 g